Publicidad
Idiomas disponibles
Idiomas disponibles
Printer Installation Guide & Safety Guide
◈ Information
This installation guide contains quick information required for the product installation. Refer
to the User's Manual in the CD that comes with the product for detailed installation
instructions. The CD contains the following information.
1. Manual: User's Manual, Code table, and Control commands
2. Driver: Windows driver and OPOS driver
3. Utility: Logo download tool and virtual memory switch adjustment tool
We at BIXOLON maintain ongoing efforts to enhance and upgrade the functions and quality
of all our products. In following, product specifications and/or user manual content may be
changed without prior notice.
◈ Checking the Contents
SRP-F310/312/313II
◈ Connecting Cables
1. Turn off the printer and ECR (host computer).
2. Connect the power cord to the adapter and connect the adapter to the power supply
connector of the printer.
3. Check the type of the interfaces at the back of the printer (
Powered USB, Wireless LAN, Bluetooth
4. Connect the drawer kick-out cable to the drawer kick-out connector of the printer.
Power Cable
Interface Cable
◈ Installing Paper Rolls
※ Do not use paper wider than 80 mm or plastic paper tube when using a printer
that specifies 80 mm paper.
◈ Using 83mm Paper
Remove the partition installed in the printer to use 83mm roll paper.
※ Refer to the User's Manual for detailed instructions on how to remove the
partition safely.
Front Printing Thermal Printer SRP-F310/312/313II
Power Cord
Procuct Installation CD
Procuct Installation CD
Procuct Installation CD
CD
Installation Guide
Serial, Paralle, USB, Ethernet,
), and connect the interface cable.
Drawer Kick-Out Cable
USB Dongle
Ethernet
Power
Serial, Paralle, Powered USB,
Wireless LAN, Bluetooth
1. Press the [Open Cover] button and open
the cover.
2. Insert new paper roll in the correct
direction.
3. Pull the paper slightly, and close the
cover.
※ Note
When closing the cover, hold down the
center of the cover so that the paper is
closely attached to the roller.
Printing quality may not be optimum if
recommended paper is not used.
(Refer to the User's Manual.)
◈ Using Operation Panel
• POWER indicator
Blue light will be on when power is supplied to the printer.
• ERROR indicator
Red light will be on for error conditions such as no paper or open cover.
• PAPER indicator
Red light will be on when the paper is about to run out or if there is no paper. If this light
keeps blinking, it means either self test state or macro execution standby state.
• FEED button
Press feed button to feed the paper. Pressing and holding the feed button will feed the paper
continuously.
◈ DIP switch setting
DIP switch setting must be done while the printer is turned off. Changes during power on are
not recognized.
Paper Roll
1. Serial interface setting
• DIP switch 1
Switch
1-1
Auto-Cutter Selection
1-2
1-3
1-4
1-5
1-6
1-7
1-8
2. Parallel / USB / Ethernet / Wireless LAN / Powered USB interface setting
• DIP switch 1
Switch
1-1
Auto-Cutter Selection
1-2
1-3
1-4
1-5
1-6
1-7
1-8
3. Bluetooth interface setting
• DIP switch 1
Switch
1-1
Auto-Cutter Selection
1-2
1-3
1-4
1-5
1-6
1-7
1-8
• Table 1 – Baud rate(bps) selection
Baud rate
2400
4800
9600
19200
38400
57600
115200
※ Auto Cutter Enable / Disable selection
SW1 - 1
Application
Function
ON
Disable
Handshaking
XON/XOFF
Word length
7 bit
Parity check
YES
Parity selection
EVEN
Baud rate (bps)
Refer to Table 1 shown below
Function
ON
Disable
N/A
-
N/A
-
N/A
-
N/A
-
N/A
-
N/A
-
N/A
-
Function
ON
Disable
N/A
-
SSP Mode
Enabled
N/A
-
N/A
-
N/A
-
N/A
-
N/A
-
1-6
ON
OFF
ON
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
OFF
ON
ON
Dip Switch Set 1
ON
OFF
Ignores Auto Cutter error for continuous printing
OFF
Default
Enable
OFF
DTR/DSR
OFF
8 bit
OFF
NO
OFF
ODD
OFF
OFF
ON
OFF
OFF
Default
Enable
OFF
-
OFF
-
OFF
-
OFF
-
OFF
-
OFF
-
OFF
-
OFF
OFF
Default
Enable
OFF
-
OFF
Disabled
OFF
-
OFF
-
OFF
-
OFF
-
ON
-
OFF
1-7
1-8
Default
OFF
ON
OFF
OFF
9600
ON
ON
ON
Auto Cutter Disable
Auto Cutter Enable
Publicidad
