How To Assemble The Sprayer - Volpi v.black Kompress Manual Del Usuario

UK Manual pre-compression sprayer
INSTRUCTIONS FOR USE: the presents instructions for use are part of the sprayer, preserve them in a
safe place and nearby the sprayer to have it at disposal if needed. Before using or doing the
maintenance of the sprayer, it is recommended to read carefully the instructions and to follow strictly
the warnings and the information reported, to use it correctly and safely.
WARNINGS: This sprayer is intended to the delivery of liquid solutions with density lower than 1,1
and heat not higher than 40°C. It is important to strictly follow the instructions provided by the
producer of the substance delivered.
Do not deliver products without being in possession of technical datas provided by the productor.
Under no circumstances it is ever possible to use the sprayer with solvents, acids, flammable and
explosive liquids, corrosive liquids, disinfectant agents and impregnating agents.
Do not use the sprayer with pesticides. Only use plant protection products authorised by the Minister
of Health. Children, people under 16 years old and pregnant ladies cannot use the sprayer, while
mentally and sensory disabled only under supervision. Do not use the sprayer if tired, ill or under the
effects of alcohol, drugs or medicinal products. The sprayer is designed only for manual use. Use the
sprayer only for intended purpose. An inappropriate use of the sprayer can be dangerous. Always
wear protective clothes and devices (coveralls, gloves, mask, glasses) to avoid contact with harmful
and toxic products. Prepare the solution in an external container and not directly in the tank of the
sprayer. Pay attention not to breathe in steam and drops of the delivered solution. In case of contact
and accidental breath in, consult a doctor. Do not eat, drink or smoke during the treatment. Do not
blow into the nozzles with the mouth. Use the sprayer in wide working areas not windy. In windy
situations, do not spray upwind. Keep the sprayer away from children and pets. Do not spray nearby
waters with fishes. Keep the sprayer away from heat sources, do not leave it exposed to the sunlights
or to cold weathers for long time. Do not disperse in the environment the chemical products leftover.
Do not use incorrectly the pressure discharge valve. Do not pressurize the sprayer with external
equipment (compressors, etc.). Do not unscrew the closing parts if the tank is in pression. Before
opening the tank of the sprayer, make sure the sprayer is completely depressurized. Do not
pressurize the sprayer unnecessarily. Do not use incorrectly or alter the sprayer in any way.
Before each use, verify the conditions of the sprayer. Do not leave it unattended full and under
pressure. The sprayer must always be placed on an horizontal and straight floor. After the use of the
sprayer, wash carefully your hands, your face and the clothes used. The eventual reparations must be
done only by the assistance service or by the authorised technicians. Use only original spare parts.
LIMITED RESPONSIBILITY: the producer is not responsible for damages caused by the sprayer
whenever those would have been caused by a non-application of the manual of instructions, by an
misuse, by an inappropriate reparation or by the substitution of spare parts with non original ones
and the reparation has not been done by the assistance service or by a technician properly authorised
by the producer. What mentioned above is valid also for the components and accessories.
HOW TO ASSEMBLE THE SPRAYER: unscrew the ring M from the handgrip E and insert it in the lance
L; insert the lance into the beginning of the handgrip E; tighten the ring M on the handgrip E (fig. 1).
Unscrew the ring N from the handgrip E and insert it into the pipe G; stick completely the tip of the
pipe G on the rubber holder of the handgrip E; tighten until the end the ring N on the handgrip E
(fig.1). Insert the ring C on the pipe G; insert completely the tip of the pipe G on the rubber holder of
the tank A; tighten until the end the ring C on the tank A (fig. 2). Insert the shoulder strap into the
slots of the sheath H (fig. 3). Insert the tip of the strap F into the slots of the tank A as reported in the
picture (fig. 4).
HOW TO FILL THE TANK: pull the knob of the pressure discharge valve (fig. 5) to ensure the tank is not
in pressure and the valve works regularly. Unscrew the pump B and remove it; pour the solution
Pag. 8 di 60