IKEA FREKVENS Manual De Instrucciones página 4

ENGLISH
TABLE OF CONTENTS
1. Volume Control
2. Power on/off
3. AC IN
4. AC OUT
5. AUDIO IN
6. AUDIO OUT
7. SUBWOOFER OUT
8. Handle with jumpers
9. Cover
10. Foot
11. Battery compartment lid for
BRAUNIT battery pack, sold
seperately
Getting started
1. Connect mains cord into AC In (3)
connector.
2. A quick press on the button (2) turns
the speaker on/off. White LED is now
on. If a paired device is found, the
LED shines without blinking and your
speaker is ready to use.
3. If no device is found the speaker
LED continues to blink and enters
pairing mode automatically. Go to
the Bluetooth settings in your mobile
device and connect to FREKVENS
10x20. The LED should now stop
blinking and your speaker is ready to
use. If no music has been playing for
20min, the speaker will enter sleep
mode.
Adjust Volume
Turn the knob (1) left to decrease or
turn it right to increase volume level.
Pair Bluetooth device(s)
(maximum 8 devices can be stored)
1. Go to your Bluetooth menu on
your mobile device and connect to
FREKVENS 10x20.
2. Once Bluetooth connection is
established, the white LED stops
blinking.
Unpair Bluetooth device
Go to your Bluetooth menu on your
mobile device and unpair FREKVENS
10x20 from your devices.
Using an external source
Connect the external source to the
AUDIO IN (5) jack on the rear panel.
The speaker automatically detects the
external input and disables Bluetooth
functionality. Use a 3.5mm 3-pol Audio
cable for this feature.
Using and charging the speaker
FREKVENS 10x20 has the possibility to
be portable. BRAUNIT battery pack is
sold separately.
• To insert the battery, open the
compartment lid (11) and insert the
battery in the correct direction.
• The battery is charged in the product
when mains cord is connected.
• When battery is low a red LED at the
button (2) will flash. During charging
the red LED is on.
Accessories
Covers: pull off to detach and push on
to attach.
Handle and jumpers: Attach/remove
with two jumpers and four screws using
an Allen key.
Factory reset
Press button (2) 10 sec. This deletes all
paired Bluetooth devices.
Safety and important notice
WARNING:
— Risk of overheating! Never install
the product in a confined space.
Always leave a space of at least
5 mm around the product for
ventilation. Ensure curtains or other
objects never cover the ventilation
slots on the product.
— Never place the product or batteries
near open flames or other heat
sources, including direct sunlight.
— Only use this product indoors. The
apparatus shall not be exposed to
dripping or splashing, no objects
filled with liquids, such as vases,
shall be placed on the apparatus.
— Never place this product on other
electrical equipment.
— The mains plug or an appliance
coupler is to be used as a disconnect
device, the disconnect device shall
remain readily operable.
— If the supply cord is damaged,
replace it with a new cord set which
is type-approved for your country.
— Batteries (battery pack or batteries
installed) shall not be exposed to
excessive heat such as sunshine,
fire or similar.
IMPORTANT!
— The speaker is for indoor use only
and can be used in temperatures
ranging from 0º C to 45º C.
— Do not leave the speaker in direct
sunlight or near any heat source, as
it may overheat.
— Do not subject the speaker to
wet, moist or excessively dusty
environments, as this may cause
damage.
— The range between the speaker and
the receiver is measured in open air.
— Different building materials and
placement of the units can affect the
wireless connectivity range.
— Too high volume can damage your
hearing.
— Do not touch the acoustic
components.
— Do not use the product as a shelf or
stand.
4