Remote Control Battery Replacement; Replacing The Light Bulbs - QualityCraft MM905-48BCP Guia Del Usuario

Once the heater is switched off, the indicator light will flash and the unit will keep
working with the air flow for 5 more seconds.
: Press this button once for flame effect. The unit will beep and the indicator
light will be ON. The bulbs for flame effect and log-set will be ON. To adjust
the flame intensity, hold down the button – the flame optics will go higher or
lower. Once you have found the desired setting, release the button. Pressing
the button again will stop the light function.
750w: Press this button for low heat level. The unit will beep and the indicator light
will be on. The fireplace heater will give low heat level. Pressing once again will stop
the low heat level function.
1500w: Press this button for high heat level. The unit will beep and the indicator
light will be on. The fireplace heater will give high heat level. Pressing once again will
stop the high heat level function.
Temperature Control: To adjust the temperature to your individual requirements,
turn the temperature control dial to the right (clockwise) to increase the desired
temperature and to the left for lower temperature. This temperature control dial can
only be used while the 0/I switch, standby switch and 750W/1500W switches are in
the ON position.
NOTe: When the O/I or standby switch is turned off, all other heater functions will
stop even though the switches may be in the on position.
NOTe: In order to shut down the heater safely, it is recommended to turn the
temperature control knob to lowest setting and allow the heater to cool down before
press the 0/I or standby switch to off position.
OPErAtiON BY tHE rEMOtE cONtrOl
Plug in your electric fireplace heater and it will beep once. This means you have
power and your remote is ready to operate your electric fireplace heater.
: Press this button once the unit becomes energized and you can select the
following functions as desired. Press this switch again, the unit will be OFF
and enter the standby mode.
Once the heater is switched off, the indicator light will flash and the unit will keep
working with the air flow for 5 more seconds.
: Press this button once for flame effect. The unit will beep and the indicator
light will be ON. The bulbs for flame effect and log-set will be ON. To adjust
the flame intensity, hold down the button – the flame optics will go higher or
lower. Once you have found the desired setting, release the button. Pressing
the button again will stop the light function.
750w: Press this button for low heat level. The unit will beep and the indicator light
will be ON. The fireplace heater will give low heat level. Pressing once again will stop
the low heat level function.
1500w: Press this button for high heat level. The unit will beep and the indicator
light will be ON. The fireplace heater will give high heat level. Pressing once again
will stop the high heat level function.

rEMOtE cONtrOl BAttErY rEPlAcEMENt

Replace with 2 AAA batteries.
wARNINg: dO NOT MIx Old ANd New BATTeRIes. dO NOT MIx AlkAlINe,
sTANdARd (CARBON-ZINC), OR ReChARgeABle (NICkel CAdMIuM)
BATTeRIes.
MAiNtENANcE
wARNINg: Disconnect power and unplug the power cord before attempting any
maintenance or cleaning to reduce the risk of fire, electric shock or damage
to persons. The bulbs in your unit can become extremely hot. Allow at least 10
minutes between turning off the unit and removing the light bulbs to avoid the
accidental burning of the skin.
RIsk Of fIRe: dO NOT exCeed The ReCOMMeNded BulB wATTAge.

rEPlAciNG tHE liGHt BUlBS

Step 1: Remove 12 screws on the back of fireplace and open the rear cover.
Step 2: You will find 1x40W type B-10 bulbs under the log-set bed.
Step 3: Loosen and remove the burnt out bulb and replace with new bulb.
Step 4: Close the rear cover. Secure the 2 larger screws into the top left corner hole
and bottom right corner holes as shown in the diagram. Secure the 10 smaller
screws into the remaining holes. Make sure the screws are in the correct holes
and have been tightened.
Step 5: Plug in the unit.
rEPAir SEt
4