Replacing The Filters - Black and Decker HLVC315B Manual De Instrucciones

Aspiradora inalámbrica
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

English
MAINTENANCE

WARNING:
serious personal injury, turn unit off and lock
off the tool before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
Your BLACK+DECKER power tool has been designed to
operate over a long period of time with a minimum of
maintenance. Continuous satisfactory operation depends
upon proper tool care and regular cleaning.
Cleaning

WARNING:
of all air vents with clean, dry air at least once a
week. To minimize the risk of eye injury, always
wear ANSI Z87.1 approved eye protection when
performing this procedure.

WARNING:
harsh chemicals for cleaning the non‑metallic parts
of the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid get
inside the tool; never immerse any part of the tool into
a liquid.
Dust Bowl (Fig. G)

WARNING:
vacuum without its filters.
iMPORTAnT: Maximum dust collection will only be
obtained with clean filters and an empty dust bowl. If dust
begins to fall back out of the product after it is switched off,
this indicates that the dust bowl is full and requires emptying
To Empty the Dust Bowl (Fig. g)
1. Place the dust bowl over a trash bin and remove the dust
bowl 
 5 
from the main housing 
bowl 
 5 
counterclockwise and pulling the dust bowl
away from the main housing.
2. Remove the filter assembly 
dust bowl 
 5 
.
3. Shake or lightly brush any dust from the filter assembly.
4. Empty the dust from the dust bowl 
and wash if necessary. Ensure that the dust bowl is
completely dry before using.
5. Place filter assembly into position in the dust bowl.
6. Install the dust bowl 
ensuring the dust bowl tabs 
housing slots 
 17 
as shown in Fig. G and rotate the dust
bowl clockwise to lock it firmly into position.
8
To reduce the risk of
Blow dirt and dust out
Never use solvents or other
Never use this cordless hand
 4 
by twisting the dust
 10 
by pulling it out of the
 5 
into a trash bin
 5 
onto the main housing 
 18 
aligns with the main
Cleaning the Filters (Fig. G)
Removing Pre‑filter
1. Place the dust bowl over a trash bin and remove the dust
bowl 
 5 
bowl 
 5 
away from the main housing.
2. Remove the filter assembly 
dust bowl.
3. Twist counterclockwise and pull the pre-filter 
seperate it from the filter 
4. Remove the pre-filter and shake or lightly brush any dust
from the filter and pre-filter.
5. Empty any dust from the dust bowl 
and wash if necessary. Ensure that the dust bowl is
completely dry before using.
6. Wash the pre-filter 
warm, soapy water. Ensure that both are completely dry
for 12 hours before using.
7. Install the pre-filter onto the filter, ensuring the filter
tabs 
 20 
pre-filter clockwise to lock it firmly into position.
8. Install the filter assembly into the dust bowl.
9. Install the dust bowl onto the main housing, ensuring
the dust bowl tabs 
slots 
 17 
clockwise to lock it firmly into position.
Cleaning the Filter
1. Once the filter and pre-filter are removed from the
dust bowl shake off or lightly brush any dust from the
pre-filter 
2. Rinse out the dust bowl with warm soapy water.
3. Wash the filters regularly using warm, soapy water and
ensure that it is completely dry before using again. The
cleaner the filter is, the better the product will perform.
4. It is very important that the filters are completely dry and
correctly in position before use.
5. Ensure the filters are completely dry for 12 hours
before refitting.
6. Follow instructions in the Removing pre‑filter section for
assembly instructions.

Replacing the Filters

The filters should be replaced every 6 to 9 months and
whenever worn or damaged. Replacement filters are
available from your BLACK+DECKER dealer.
Visit www.blackanddecker.com to locate dealers.
Remove the old filters as described in Cleaning the Filters.
Fit the new filters as described in Cleaning the Filters.
Only use BLACK+DECKER replacement filter: HLVCF10
 4 
,
from the main housing 
 4 
counterclockwise and pulling the dust bowl
 10 
by pulling it out of the
 12 
.
 11 
and filter 
 12 
aligns with the pre-filter slots 
 18 
aligns with the main housing
as shown in Fig. G and rotate the dust bowl
 11 
and filter 
 12 
.
by twisting the dust
 11 
to
 5 
into a trash bin
regularly using
 19 
and rotate the

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Hlvc315jHlvc320jHlvc320b

Tabla de contenido