Storage Recommendations - Black and Decker HLVC315B Manual De Instrucciones

English
..................... read all
BATTERY AND CHARGER
The battery is not fully charged out of the carton. Before using
the charger to charge the battery, read the safety instructions
below and then follow charging procedures outlined.
Only for use with S003AQU1500015 chargers.
READ ALL INSTRUCTIONS
Important Safety Instructions for All
Integral Battery Tools

WARNING:
instructions, and cautionary markings for the
battery, charger and product. Failure to follow the
warnings and instructions may result in electric
shock, fire and/or serious injury.
NEVER force a charger plug into the tool.
•
DO NOT modify the charger plug of a non‑compatible
•
charger in any way to fit into the tool as the battery
may rupture causing serious personal injury.
DO NOT charge or use the battery in explosive
•
atmospheres, such as in the presence of flammable
liquids, gases or dust. Inserting or removing the charger
plug from the tool may ignite the dust or fumes.
Only charge the battery with the provided charger.
•
DO NOT splash or immerse in water or other liquids.
•
• DO NOT allow water or any liquid to enter tool.
DO NOT store or use the tool in locations where the
•
temperature may reach or exceed 104 °F (40 °C) (such
as outside sheds or metal buildings in summer). For
best life store tools in a cool, dry location.
NOTE: Do not store the tool with the switch locked on.
Never tape the switch in the ON position.
• DO NOT incinerate the tool even if it is severely
damaged or is completely worn out. The battery can
explode in a fire. Toxic fumes and materials are created
when lithium‑ion batteries are burned.
If battery contents come into contact with the skin,
•
immediately wash area with mild soap and water. If
battery liquid gets into the eye, rinse water over the open
eye for 15 minutes or until irritation ceases. If medical
attention is needed, the battery electrolyte is composed of a
mixture of liquid organic carbonates and lithium salts.
• Contents of opened battery cells may cause
respiratory irritation. Provide fresh air. If symptoms
persist, seek medical attention.
Battery liquid may be flammable if exposed to spark
•
or flame.
• Never attempt to open the tool for any reason. If the
tool case is cracked or damaged, do not charge. Do
not crush, drop or damage the tool. Do not use a tool or
charger that has received a sharp blow, been dropped, run
over or damaged in any way (e.g., pierced with a nail, hit
with a hammer, stepped on). Damaged tools should be
returned to the service center for recycling.
6
documentation
Read all safety warnings,

Storage Recommendations

The best storage place is one that is cool and dry, away
from direct sunlight and excess heat or cold. Store the fully
charged tool disconnected from the charger.
Transportation
nOTE: Integral Li-ion tools should not be put in checked
baggage on airplanes and must be properly protected from
short circuits if they are in carry-on baggage.
Tool Disposal
This product uses a lithium-ion rechargeable and recyclable
battery. When the battery no longer holds a charge, the tool
should be recycled. The tool should not be incinerated or
placed in the trash.
The tool can be taken for disposal to an Authorized Service
Center. Some local retailers are also participating in a national
recycling program (refer to RBRC®). Call your local retailer for
details. If you bring the tool to an Authorized Service Center,
the Center will arrange to recycle the tool and its battery.
Or, contact your local municipality for proper disposal
instructions in your city/town.
Charging the Battery (Fig. B, C)
(HLVC315J, HLVC320J Only)

WARNING:
supplied charger.

WARNING:
at ambient temperatures below 39 °F (4 °C) or above
104 °F (40 °C).
From new, the rechargeable cells of the product need a
minimum charge time of 10 hours for HLVC315J and 13 hours
for HLVC320J to ensure full power.
1. The switch must be in the OFF position, the appliance
will not charge if it is in any other position.
2. Fig. B - Plug the jack plug
charging socket 3 of the tool.
3. Plug the charger 15
electrical outlet.
4. The charge indicator LED
housing 4 will illuminate while charging.
5. The charge indicator LED
completion of charging.
nOTE: While charging, the charger may get warm,
this is perfectly normal and safe. It is safe to leave the
appliance connected to the charger indefinitely. The
charger automatically reduces power consumption when
charging is complete.

WARNING:
at ambient temperatures below 39 °F (4 °C) or
above 104 °F (40 °C).
For use only with the
Do not charge the battery
16 of the charger into the
into any standard 120 Volt 60 Hz
on the center of the main
13
13 will turn off upon
Do not charge the battery