SIMPLE™ KEY USER GUIDE
NOTE: If the EZ Installer™ is left in the vehicle's on-board diagnostic
(OBD) port for more than 5 minutes, an alarm will sound reminding you to
remove it.
NOTE: If at any point the EZ Installer™ continues to beep rapidly, please
refer to the FAQ section for more information.
1.
Find your vehicle's make, model, and year in the Compatibility Lookup
on page 3. Turn the dial on the EZ Installer™ to the position listed for
your vehicle's make, model, and year.
NOTE: If more than one dial position exists for your vehicle, try the
PRIMARY dial position first. If you are unable to successfully pair the
key, try the ALTERNATE dial position listed for your vehicle.
NOTE: All existing, working keys and the new key should be present
during the pairing process.
2.
Enter the vehicle and ensure all doors are closed.
3.
Begin with the vehicle in PARK and the engine OFF.
4.
Turn hazard lights ON.
5.
Insert the original key into the ignition and start the vehicle.
6.
Remove the security label from the EZ Installer™ and insert it firmly
into the on-board diagnostic (OBD) port located under the dash.
a.
The location of your vehicle's OBD port can be found in your
owner's manual.
7.
Wait up to 8 seconds and listen for 3 quick beeps from the EZ Installer™.
a.
NOTE: If you hear a series of more than 3 rapid beeps, an error
has occurred. Please see FAQs to learn more.
8.
Turn the ignition off and remove the key.
9.
Review the chart below and proceed based on your EZ Installer™ dial position.
For DIAL POSITION 4
For ALL OTHER DIAL POSITIONS
CDJ IGNITION POSITIONS
6
Insert the key into the ignition
only, DO NOT turn to the ON/RUN
position.
Insert the new key and turn the
ignition to the ON/RUN position.
SIMPLE™ KEY USER GUIDE
10.
To continue, press and release the EZ Installer™ button.
11.
Wait up to 8 seconds and listen for 3 quick beeps from the EZ Installer™.
a.
NOTE: If you hear a series of more than 3 rapid beeps, an error
has occurred. Please see FAQs to learn more.
12.
Turn the ignition off and remove the key.
13.
To continue, press and release the EZ Installer™ button.
14.
The EZ Installer™ will chime when pairing is complete.
15.
Unplug the EZ Installer™. If the EZ Installer™ is left in the OBD port for
more than 5 minutes, an alarm will sound, reminding you to remove it.
16.
To pair additional keys, unplug the EZ Installer™ from the OBD port.
Repeat the pairing process for any additional keys, beginning with
PAIRING STEP 1.
17.
Test all keys.
18.
Turn hazards off.
FREQUENTLY ASKED QUESTIONS
Q: The EZ Installer™ beeps 8 times after pushing the button to initiate the
pairing process and will not pair the new key.
A: Your vehicle allows a maximum of 8 paired keys. If the vehicle already
has 8 keys paired to it, a new key cannot be paired. If the EZ Installer™
beeps 8 times early in the pairing process, this indicates that the maximum
number of keys have been paired. Please contact Car Keys Express
customer service at 888-598-8910.
Q: Can I use the same EZ Installer™ on other vehicles?
A: No, the EZ Installer™ will be locked to the first vehicle it is used on.
You may add more keys to the same vehicle again as needed, but it will
not work on different vehicles. If the EZ Installer™ sounds 2 beeps at 1
second intervals, then beeps rapidly, this signifies that the device has
already been used on another vehicle. Visit CKESimpleKey.com or your
local retailer to purchase additional keys.
Q: The EZ Installer™ sounds 2 or 3 beeps at 1 second intervals 3 times then beeps
continuously.
A: When problems occur during the pairing process, EZ Installer™ will
beep an error code, followed by continuous faster beeps. The number of
error beeps correspond to specific error codes, explained below.
•
Two distinct beeps at 1 second intervals indicate the device has
already been used on another vehicle. The EZ Installer™ can only
pair Simple™ Keys to one vehicle. The EZ Installer™ will be locked to
the first vehicle it is used on. You may add more keys to the same
vehicle again as needed, but it will not work on different vehicles.
7