Sharp XE-A301 Guia De Inicio Rapido

Quick Start/A4(En) 03.4.24 7:46 PM Page 1
XE-A301 Quick Start Guide
For quick set-up, follow the steps shown below. Note that malfunction may occur if you do not follow the steps. For further information, please read the instruction manual. For installing the cash register, find a stable
surface near an AC outlet where the cash register will not subject to water sources or direct sunlight.
Installing the Cash
1 2
Register
Install the cash register using the fixing
To ensure the cash register operates properly, initialize it using
angle bracket provided with the register.
the following procedure.
1. Make sure the power cord is not inserted into the AC outlet.
1. Thoroughly clean the location where
2. Insert the manager (MA) key into the
the fixing angle bracket (B) is to be
mode switch and turn it to the PGM
placed.
position.
2. Peel off the adhesive tape on the
fixing angle bracket.
3. While holding down both the
3. Hook the angle bracket onto the hook
the plug into the AC outlet. The buzzer will sound three times
(A) that is located at the bottom rear
and "
of the register.
4. The cash register has now been initialized.
4. Firmly stick the fixing angle bracket to
The register display will show "0.00" with "PGM".
the table surface that your cleaned
CAUTION: To charge the rechargeable batteries, keep the power
above.
NOTE: If you press a key by mistake, an error message may be
3
A
1. Lift the rear of the printer cover and
B
detach it.
To remove the resister from the fixing
angle bracket:
1. Lift up the front of the register and
2. Remove the white retainer at
pull the register towards you.
the position shown at the
right.
NOTE: Please keep this
retainer for future use when
transferring the cash register.
3. Move the print head release
lever upwards as illustrated
at the right.
Initializing the Cash Register
REG
OPX/Z MGR
X1/Z1
X2/Z2
PGM
} l
key and the key, insert
MRS. " will be displayed.
*** ***
on for one or two days. Leave the register with the
" "
mode switch in a position other than .
l
displayed. Press the key to clear message after
installing paper rolls.
Preparing for the Printer
Retainer
Print head
release lever
Installing the Paper Rolls
4
1. Cut off approximately one revolution of each paper
roll.
Make sure the paper end is cut as illustrated below.
Correct Incorrect
For receipt paper installation
2. Set a paper roll in the paper cradle of the receipt side
(left side) as illustrated below.
To the printer To the printer
Correct Incorrect
3. Insert the end of the paper
into the paper chute until it
is caught by the printer
auto-feed and comes out
the top of the printer. If
the printer does not catch
the paper, feed the paper
{
while pressing .
4. Cut off the excess paper with the paper cutter.
For journal paper installation
5. Set a paper roll in the paper cradle of the journal side
as illustrated in step 2.
6. Insert the end of the paper
into the paper chute until it
is caught by the printer
auto-feed and comes out
the top of the printer. If
the printer does not catch
the paper, feed the paper
}
while pressing .
7. Insert the end of the paper into the slit in the take-up
spool and wind the paper two or three turns around
}
the spool shaft. (Press to feed more paper if
required.)
}
8. Set the spool on the bearing, and press the key to
take up excess slack in the paper.
9. Replace the printer cover.
English
Basic Programming
5
Set the mode switch to the PGM
position.
Setting the Date
Enter the date in 8 digits using the day-
month-year format. Then press s .
Example: Date (26 August, 2003)
s
26082003
Setting the Time
Enter the time in 4 digits ("hhmm"
format) using the 24 hour system. Then
press s .
Example: Time (2:30 p.m.)
s
1430
Setting the VAT
Set the VAT rate in seven digits (3-digit
integer and 4-digit decimal).
Example: VAT1 rate 16%
s
9 @ 1 @
16 @s A
NOTE: Department 1 to 99 are set VAT1
by default.
Other programming
While the cash register is
preprogrammed so that it can be used
with minimal setup, you may need to
program some items such as
department texts and logo message.
For details of programming, please refer
to the instruction manual.
Now, you are ready for
6
sales entries.
Set the mode switch to te REG position,
and start registration. For details of
registration, please refer to the
instruction manual.