LANDMANN HeatWave 28007 Instrucciones De Armado Y Uso página 3

ASSEMBLY INSTRUCTIONS
A Phillips or plain screwdriver and
an adjustable wrench is needed for
assembly.
Assembly time: 45 minutes
STEP 1: ASSEMBLE FIREBOWL HANDLE
Assemble the firebowl handle [ T ] to the
front of the firebowl [ E ] using (2) 12mm
bolts [ O ], hexnuts [ P ] and flat washers [ N ].
Assemble the bolts and washers from inside
the firebowl. Tighten bolts securely.
STEP 2: ASSEMBLE FRONT LEGS
Assemble the front legs [ L ] to the firebowl
[ E ] using (2) 12mm bolts [ O ], hexnuts [ P ]
and flat washers [ N ] per leg. Note the
front legs are assembled closest to the
firebowl handle. Tighten bolts securely.
STEP 3: ASSEMBLE WHEEL LEGS
Assemble the wheel legs [ F ] to the firebowl
[ E ] using (2) 12mm bolts [ O ], hexnuts [ P ]
and flat washers [ N ] per leg. Tighten bolts
securely.
STEP 4: ASSEMBLE WHEELS
First, assemble each wheel bracket [ G ] to the
wheel leg [ F ] using (2) 12mm bolts [ O ] and
hexnuts [ P ] per bracket. Next, assemble the
wheel [ H ] to the bracket using (1) 45mm
bolt [ K ], large washer [ R ], lock washer [ S ]
and M8 hexnut [ Q ]. Make sure all bolts
securely tightened.
STEP 5: ASSEMBLE FIREBOWL HANDLE
SHIELD
Assemble the firebowl handle shield [ U ] to
the handle [ T ] using (2) 12mm bolts [ O ]
and hexnuts [ P ]. Tighten bolts securely.
STEP 6: ASSEMBLE SPARK SCREENS TO
FORM THE SPARK GUARD
Assemble the (4) spark screen panels [ C ]
together using (2) 12mm bolts [ O ], lid tabs
[ D ] and hexnuts [ P ] per panel. Make sure
the lid tabs are assembled properly from the
inside with the tab outwards. Adjust each
panel so there are no gaps between the
frames before tightening the bolts securely.
STEP 7: PLACE SPARK GUARD ONTO THE
FIREBOWL
Place the assembled spark guard in the
firebowl [ E ]. The spark guard will slide into
the firebowl about 1.5 in. until it rests on the
curved bottom.
STEP 8: PLACE WOOD GRATE
Place the wood grate [ J ] on the firebowl [ E ]
bottom. Make sure wood grate is used at all
times.
STEP 9: ASSEMBLE THE LID HANDLE
AND LID HOOK
Assemble the lid handle [ A ] and lid hook
[ W ] to the lid [ B ] using (2) 12mm bolts
[ O ], flat washers [ N ] and hexnuts [ P ].
Tighten bolts securely.
STEP 10: PLACE LID
Place assembled lid onto the lid tabs [ D ].
ADD SAND TO FIREBOWL
Before using, add a 1-1.5 in. layer of sand or
about 5 lbs. (size wise, its the same amount as
a 5 lb. bag of sugar) to the bottom of the
firebowl. This will help against the corrosive
nature of the ashes and help radiate the heat
upwards.
W
IMPORTANT!
LID TABS ARE
D
ASSEMBLED ON
THE INSIDE.
O
C
IMPORTANT!
J
USE WOOD GRATE
AT ALL TIMES.
N
E
F
O
G
R S
G
K
H
O
N
P
P
O
N
O
P
Q
DO NOT RETURN PRODUCT TO THE STORE.
TROUBLE WITH ASSEMBLY, PLEASE CALL
A
B
C
THE LID HOOK
CAN BE USED TO
HANG THE LID ON
THE SPARK GUARD
WHEN ADDING
FIREWOOD OR
TENDING THE FIRE.
IMPORTANT!
ADD 5 LBS OF
SAND TO THE
BOTTOM OF THE
FIREBOWL.
P
L
IF YOU HAVE QUESTIONS OR HAVE
1-800-321-3473 FOR ASSISTANCE.
PAGE 3
W
U
O
T
P