Product Service - YATO YT-85120 Manual De Instrucciones

GB
Avoid accidental switching on of the pole pruner. In the case of transporting the pole pruner that is connected to the mains or to
connected to battery, you must keep your fingers away from the power switch.
Always wear the correct, adjacent to the body, protective clothing.
Always operate the pole pruner by holding it with both hands. While you are working you should secure loose pieces of wood,
so that they
are prevent from moving, for example, by placing in them in a saw ing jack. You should avoid cutting the wood, which is located
on the ground. You should avoid
to process the wood, which is not secured against its movement during cutting.
During operation you should not hold the pole pruner above your shoulders. You should not work with the pole pruner, while you
are on the tree. You should adopt such an position when you are working, that there would be no need to draw hands for a full
length.
Keep the chain clean. The chain must be sharpened and lubricated. This will ensure a more efficient and safer
work. The chain can be sharpened in a specialized service. Before each use, check the condition of chain..
If you find cracks, broken out teeth or any other damage, you should, before the start of the
work, replace the chain with a new one.
In the case when you notice any damaged or broken parts of the pole pruner, you should stop the work nor to start it. Damaged
parts must be replaced before the starting of work.
The pole pruner must be used in accordance with the intended use, it is designed only for wood cutting. When you work, you must
be careful on metal elements or stones, which may be found in the processed wood.
Use only genuine spare parts. Usage of non-original spare parts may increase the risk of
failure and lead to a body injury.
The pole pruner should be repaired only in services, which has been authorized by the manufacturer. Use original spare parts.
This will minimize the risk of accidents and damage to equipment.

PRODUCT SERVICE

Preparation of the pole pruner to work
Attention! Before all mounting and regulatory operations, you should disconnect the pole pruner from the power supply. The tool,
which is mains powered, should be disconnected from the wall outlet, the pole pruners, which are battery operated, should be
disconnect from the battery.
Before using the pole pruner for a first time, you must mount the guide and cutting chain.
Installation does not require any tools, however, for security reasons, it should be carried out with protective gloves.
Loosen the locking knob so that it is possible to remove the entire side panel.
Install the guide and chain as it is shown in the picture (II).
Make sure, that chain and guide have been installed in the right direction. The shape and direction of the links, which is visible
on the housing of the pole pruner and on the guide, should match the direction of the chain shown on pole pruner. If on the chain
there is visible the indication of movement direction of chain, then it should be in the same direction as marking on the housing
and guide.
You should not tension the chain yet, but to make sure that the chain fits in the guide row and in the teeth on the driving wheel
, Mount the side panel and tighten the locking knob. However, it should be done so it would not block the move of guide. By turning
the chain tension knob, you should adjust the chain tension. Tighten the locking knob. Check the chain tension. To do this, you
should put the pole pruner and lift it holding by the middle part of the chain (III). During
this test the chain in place of its holding should raise more than 3 to 4 mm above the guide. If the chain is tensioned too
tightly or too slightly, you should loosen the locking knob slightly and adjust the chain tension again. The chain tension should be
checked also every 10 hours of work.
Before connecting the pole pruner to power, you should check its condition. If you detect any damage it is forbidden to connect it
to the power supply before removing the damage.
In the case when the pole pruner is powered by a single-phase alternating current with a voltage of 230 V and frequency of 50
Hz, the mains socket, which is supplying the pole pruner, should be secured by a circuit breaking fuse of the tripping current of
30 mA or less.
Oil addition (IV)
Attention! Before all mounting and regulatory operations, you should disconnect the pole pruner from the power supply. The tool,
which is mains powered, should be disconnected from the wall outlet, the pole pruners, which are battery operated, should be
disconnect from the battery.
For the lubrication of the chain and pole pruner you should only use the oil, which is intended for such purposes. For the lubrication
you should not use the worn out engine oil. It does not meet its task, which can cause damage to the mechanism of pole pruner.
Make sure, that lubricating oil is in its container. You should put the pole pruner on a level surface, to check the oil indicator. The
O R I G I N A L I N S T R U C T I O N S
16