Bosch ANGLE EXACT ION 18 V-LI Manual Original página 20

20 | English
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Charging the Battery
Use only the chargers listed on the accessories page.
u
Only these chargers are matched to the lithium-ion bat-
tery of your power tool.
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
Do not continue to press the On/Off switch after the
u
power tool has automatically switched off. The battery
can be damaged.
Follow the instructions on correct disposal.
Removing the battery (see figures A1–A2)
The battery (9) is equipped with two locking levels to pre-
vent the battery from falling out when pushing the battery re-
lease button (14) unintentionally. As long as the battery is
inserted in the power tool, it is held in position by means of a
spring.
To remove the battery (9), press the release button (14)
and pull the battery forward and out of the power tool. Do
not use force to do this.
Battery charge indicator (yellow LED)
Battery Meaning
charge indic-
ator (8)
Flashing Charge the battery:
You can only drive in six to eight more
light + sound
screws.
Continuous There is not enough capacity left to drive in
light another screw or the power tool has over-
loaded:
The power tool can no longer be switched
on.
– Remove the battery and replace it with a
battery that is fully charged.
Flashing The power tool has overheated and
switched itself off:
light
– Wait a short while for the light to stop
flashing before switching the power tool
on again.
Operating and storage conditions
The power tool is suitable only for operation at enclosed
work sites.
1 609 92A 4R1 | (21.02.2019)
To ensure smooth operation, the permitted ambient temper-
ature should be between 0 °C and +45 °C, at a permitted rel-
ative humidity of between 20 and 95%, free of condensa-
tion.
Suspension device (see figure B)
You can use the hanging hook (15) to attach the power tool
to a suspension device.
– Fit the hanging hook (15) onto the power tool and make
sure it engages in the slots (16).
Depending on the centre of gravity of the power tool, you
can either use the front or back slots.
Regularly check the condition of the hanging hook and
u
the catch in the suspension device.
Switching on the worklight (see figure C)
– Press the marking ring (17) with a thin screwdriver blade,
a spatula or similar implement.
– Slide the spring ring(18) back onto the housing shell us-
ing a pair of spring ring pliers.
The two shell halves of the LED holder (12) that encase the
worklight (13) can now be brought into the required posi-
tion.
– Taking care not to damage the cable on the worklight,
slide it into the cavity provided for it (19) in the housing
shell without allowing it to bend.
– Encase the worklight (13) in the two housing shells of the
LED holder (12) once again.
– Press the spring ring (18) and the marking ring (17) back
into their original position.
Fitting the angled screw head (see figure D)
Applies to the following models:
ANGLE EXACT ION 8-1100 | 3-500 | 15-500 | 23-380 |
30-290
For these cordless angle wrenches, a suitable angled screw
head (see "Technical data", page 18) must first be fitted.
– Use the open-ended spanner (21) on the spanner flat (4)
of the angled head flange of the power tool to hold it in
place.
Never clamp the power tool to the housing shells.
u
– Place the angled screw head (3) in the required position
on the flange and use the open-ended spanner (20) on
the spanner flat (5) of the cap nut to tighten it.
While doing this, use the open-ended spanner (21) on the
angled head flange to provide resistance.
Adjusting the angled screw head
You can adjust the angled screw head (3) to a total of eight
different positions.
– Use the open-ended spanner (21) on the spanner flat (4)
of the angled head flange of the power tool to hold it in
place.
Never clamp the power tool to the housing shells.
u
– Use an open-ended spanner (20) on the spanner flat (5)
of the cap nut to loosen it. Adjust the angled screw head
Bosch Power Tools