Chicco 1-2-3 Manual Del Usuario página 12

E2 - Release tabs (2x)
F – Lower base
F1 - Leg release button (2x)
F2 - Legs (2x)
F3 - Strut slot
F4 - Saddle support slot
F5 - Rear bar slot (2x)
USE AS BABY WALKER (Fig. X)
• WARNING: Fit the rear part in the relevant
slots Fig. 1 until you hear the «Click» confirm-
ing fastening on both sides Fig. 1A.
• Fit the strut in the relevant slot in the lower
base Fig. 2.
• Adjust the height for your child by adjusting
the height of the strut while pressing the strut
height adjustment buttons C4.
• Position the upper base on the strut. WARN-
ING: Make sure the handles are in horizontal
position Fig. 3. Match the fastening buttons B2
with the handle adjustment buttons C2 until
you hear the «Click» confirming fastening Fig.
3A.
• To continue assembly, release the legs press-
ing the relevant button F1 (Fig. 4).
• Turn the legs up until they fit inside the relevant
leg fastening slots B4 as shown in Fig. 5.
• In order to correctly adjust the height make
sure that the numbers of the leg fastening
slots B4 match those on the strut C4 (Fig. 5).
• WARNING: Make sure that the legs are en-
gaged correctly as shown in Fig. 5A.
• Before using the product as a baby walker,
turn it upside down and check that all the
points shown in Fig. 6 are correctly fit.
• Fit the electronic toy panel in the relevant slot
as shown in Fig. 7, making sure that it is fas-
tened correctly.
Personalising the baby walker
IMPORTANT! The package comprises a pen-
dant fastened to the padded saddle. A series of
transparent stickers are applied on the back of it.
To personalise it, follow the instructions below:
• Visit the website WWW.CHICCO.COM and en-
ter the section dedicated to this product or
use the QR CODE on the pendant.
• Register on the website or LOG IN if you are
already have an account.
Now enter your child' s name in the relevant field
and choose your favourite design among those
available.
Once you have completed these steps, you will
automatically receive an e-mail with a printable
PDF and a document with the instructions to
complete personalisation.
USE IN FIRST STEPS CONFIGURATION (Fig. Y)
• In order to release the legs from the upper
base and to change to other configurations
(first steps and ride-on), press and release the
safety buttons B3 and legs release buttons F1
located on the upper base and legs respec-
tively as shown in Fig. 8-8A.
• To remove the upper base, pull the two han-
dle fastening buttons B2 and lift up as shown
in Fig. 9.
• Now remove the rear bar pressing the release
tabs E2 to remove it from the slots in the rear
bar F5 as shown in Fig. 10.
• Depending on the child' s height, both strut
and handles can be adjusted by means of the
adjustment buttons C4 and the buttons C2
respectively (Fig.11-11A).
• First Steps is now ready for use.
USE IN RIDE-ON CONFIGURATION (Fig. Z)
• To change into this configuration, pull out the
strut from its slot pressing the height adjust-
ment buttons C4 (Fig. 12).
• Now you can pull out the saddle from the
compartment C5 (Fig. 12A) and open the sup-
port D2 (Fig. 13).
• Fit the saddle support in the relevant slot F4
and fit the strut again in its slot F3 in the lower
base (Fig. 14).
• To complete assembly, turn the legs up until
they fit inside the leg slots in the saddle D1
until you hear a click confirming fastening in
Fig. 15.
• WARNING: Before use, check that the saddle
release button D3 is engaged and that the leg
release buttons F1 are in the position shown
in Fig. 16.
• If you need to adjust the height, repeat the
steps illustrated in Fig. 11.
• Then fit the rear bar in the relevant slots F5
(Fig. 1) making sure that you hear the «Click»
confirming fastening (Fig. 1A).
• The ride-on configuration is now ready for
use.
ELECTRONIC TOY PANEL
• The toy panel can be used in all three set-ups
fitting it inside the relevant slots (B1 - C3).
ELECTRONIC TOY – SAFETY OF THE ELEC-
TRICAL PARTS
WARNING:
• The electronic toy requires 2 1.5V AA alkaline
12