Declaration Of Conformity - Skil F0150700 Serie Manual Original

• Storage *
- store the tool indoors in a dry and locked-up place,
out of reach of children
- securely mount storage rail P on the wall with 4 screws
(not supplied) and horizontally leveled
• If the tool should fail despite the care taken in manufacturing
and testing procedures, repair should be carried out by an
after-sales service centre for SKIL power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skil.com)
TROUBlESHOOTING
• The following listing shows problem symptoms, possible
causes and corrective actions (if these do not identify and
correct the problem, contact your dealer or service station)
! switch off the tool and disconnect the plug before
investigating the problem
★ Tool does not operate
- power supply socket faulty -> use another socket
- extension cord damaged -> replace extension cord
- brush incorrectly mounted -> mount brush again
★ Tool operates intermittently
- internal wiring defective -> contact dealer/service
station
- on/off switch defective -> contact dealer/service
station
★ Weed is not removed completely
- brush damaged/worn -> replace brush
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2002/96/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 0 will remind you of this when the need for
disposing occurs

DEClARATION OF CONFORmITY

• We declare under our sole responsibility that the product
described under "Technical data" is in conformity with the
following standards or standardization documents: EN
60335, EN 61000, EN 55014 in accordance with the
provisions of the directives 2006/95/EC, 2004/108/EC,
2006/42/EC, 2000/14/EC, 2011/65/EU
• Technical file at: SKIL Europe BV (PT-SEU/ENG1),
4825 BD Breda, NL
30.07.2013
NOISE/VIBRATION
• Measured in accordance with EN 60335 the sound
pressure level of this tool is 68 dB(A) and the sound
power level 88 dB(A) (standard deviation: 3 dB), and the
vibration 3.2 m/s² (hand-arm method; uncertainty
K = 1.5 m/s²)
• Measured in accordance with 2000/14/EC (EN/ISO
3744) the guaranteed sound power level LWA is lower
than 91 dB(A) (conformity assessment procedure
according to Annex VI)
Notified body : KEMA, Arnhem, NL
Notified body identification number : 0344
• The vibration emission level has been measured in
accordance with a standardised test given in EN 60335; it
may be used to compare one tool with another and as a
preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with different
or poorly maintained accessories, may significantly
increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may significantly
reduce the exposure level
! protect yourself against the effects of vibration
by maintaining the tool and its accessories,
keeping your hands warm, and organizing your
work patterns
Brosse à mauvaises herbes
INTRODUCTION
• Cet outil a été conçu pour enlever les mauvaises herbes
des terrasses et entre les carreaux
• Cet outil n'est conçu pour un usage professionnel
• Vérifiez que le conditionnement contient toutes les
pièces présentées dans le schéma 2
• Lorsque des pièces manquent ou sont endommagées,
veuillez contacter votre distributeur
• Lisez attentivement ce manuel d'instruction avant
d'utiliser l'outil et conservez-le pour pouvoir vous y
référer ultérieurement 3
• Prêtez attention aux consignes de sécurité et aux
avertissements; ne pas suivre ces instructions peut
entraîner des graves blessures
CARACTERISTIQUES TECHNIQUES 1
ELEMENTS DE L'OUTIL 2
A Protection de coupe
B Roue
C Bouton de blocage de l'arbre
D Chapeau
E Clé
F Brosse
G Indicateur de brosse
H Douille de verrouillage
J Tube télescopique
11
k Poignée
8
0700