Publicidad
Idiomas disponibles
Idiomas disponibles
EN
1 - SAFETY WARNINGS
CAUTION – to ensure personal safety it is important to follow these instructions
and keep them for future reference.
Read the instructions carefully before proceeding with installation. The design and ma-
nufacture of the devices making up the product and the information in this manual are
compliant with current safety standards. However, incorrect installation or programming
may cause serious injury to those working on or using the system. Compliance with the
instructions provided here when installing the product is therefore extremely important.
2 - INTRODUCING THE PRODUCT
The VIP1 interface, together with the QUADRO night-time sensor and the control units of
the motors for Key Automation garage doors, enables the automatic control of additional
led lights outside and inside the garage door.
The VIP1 interface is powered by the control unit in the garage door motor, while the
QUADRO dusk sensor automatically activates up to 5 Key Automation led lights during
the night-time house.
The Night Light System switches the lights on or off 15 minutes after the set threshold
is exceeded. This delay is to prevent false switch-on or switch-off due to external light
sources such as car headlights.
CODE
DESCRIPTION
VIP1
interface for led light control
TECHNICAL SPECIFICATIONS
power supply
maximum led power
protection rating
operating temperature
dimensions (L-D-H)
ELECTRIC CABLE TECHNICAL SPECIFICATIONS
connection
cable
quadro
1 x cable 2 x 0,5 mm
led
1 x cable 2 x 0,75 mm
viper led / vip1
1 x cable 3 x 0,75 mm
3 - PRELIMINARY CHECKS
WARNING - before installing the product, perform the following checks and inspections:
• Position the QUADRO night-time sensor in a sunny area
• Position VIP1 in a sheltered are in the building
• Use electrical connections suitable for the currents required
• Check that the power supply conforms to the values in the technical specifications
4 - INSTALLING THE PRODUCT
ADJUST LED BRIGHTNESS
This setting enables adjustment of the led intensity during night-time hours
PH.
DESCRIPTION
1
Press the button S1 once
2
Led "L1" flashes briefly followed by a pause
Press and hold the button S1 for more than
3
3 seconds
4
The led remains off
5
Release button S1
The led emits 5 slow flashes
1st flash: level 1 (low brightness)
2nd flash: level 2
6
3rd flash: level 3 (factory setting)
4th flash: level 4
5th flash: level 5 (high brightness)
Press the button corresponding to the requi-
7
red brightness
8
The led emits 5 quick flashes
ADJUST AMBIENT LIGHT LEVEL
This setting enables adjustment of the light sensor activation on the basis of ambient
light
PH.
DESCRIPTION
1
Press the button S1 twice
Led "L1" emits two quick flashes followed by
2
a pause
Press and hold the button S1 for more than
3
3 seconds
4
The led remains off
5
Release button S1
VIP1
24 ÷ 32 Vdc
10 W
IP30
-20+55 °C
85-40-25
maximum permitted limit
10 m
2
20 m
2
5 m
2
EXAMPLE
x 1
x 1
> 3sec
+
+
+
+
x 5
EXAMPLE
x 2
x 2
> 3sec
The led emits 3 slow flashes
1st flash: level 1(activation with low ambient
light - factory setting)
6
2nd flash: level 2 (activation with medium
ambient light)
3rd flash: level 3 (activation with high ambient
light)
Press the button corresponding to the requi-
7
red brightness
8
The led emits 5 quick flashes
RESET VIP1
PH.
DESCRIPTION
Press the button on the receiver and hold it
down until the LED lights up (about 3 seconds)
1
and then goes out (about 3 seconds). Release
the key
About 1 second after the key is released, the
2
LED on the receiver starts to flash
To reset and restore the factory settings,
3
press the receiver button on the third flash
If the reset has been successful, the receiver
4
will give one long flash
5 - TESTING AND COMMISSIONING
The system may be put into operation after testing by a qualified technician, who must
perform the tests required by the relevant standards in relation to the risks present, to
check that the installation complies with the relevant regulatory requirements.
+
+
x 5
EXAMPLE
(>3s)->
(>3s)->
(1s)+
(1s)+
Publicidad
