Publicidad
Idiomas disponibles
Idiomas disponibles
Setting the Timer Programs
Two
program
settings are possible, P1 and P2. Only HIGH heat is
possible for program settings. Press ' ' twice, P1 AUTO ON and a time
will fl ash - see Fig. 10. The fi rst P1 ON time can now be set:
1.
Press the ' ' or '
' buttons to set the time.
2.
Press '
'.
Now P1 AUTO off is displayed, P1 OFF time can now be set:
3.
Press the ' ' or '
' buttons to set the time.
At this point either :
(a) press ' ' to exit the Program mode and return to AUTO mode. The
heater is now in AUTO mode. The heater will
OFF depending on programme P1 previously entered.
OR
(b) press ENTER to set the ON and OFF times for program
2, as in steps 1 to 3 above.
At this point press ENTER or PROG to exit the Programme mode. The
heater is now in AUTO mode. The heater will switch ON and OFF
depending on programme P1 & P2 previously entered. If after
programming and returning to the AUTO mode display, P1 or P2 is
active, the display will show PROG 1 AUTO ON or PROG 2 AUTO ON
depending on which is active - see Fig. 11. An OFF time cannot be
entered which is less than the corresponding ON time. When setting
the timer programs if no keys are pressed, the display will (after 4
minutes) revert to the previous display i.e. display prior to entering
Program mode.
Run Programs
IIf MODE is pressed until AUTO appears on the screen (either AUTO-
ON or AUTO-OFF), the heater will run both P1 and P2 program as they
are set.
NOTE: The heater cannot be programmed to run P1 only or P2
only.
To cancel P1, set P1 OFF time to be same as P1 ON time. To cancel P2
set P2 OFF time to be same as P2 ON time.
Review Program settings
To review the program settings the heater must be in AUTO mode.
Press ENTER and the times for PROG 1 ON, PROG 1 OFF, PROG 2 ON
and PROG 2 OFF will be displayed consecutively for 2 seconds. The
display will automatically return to the state it was in before ENTER
was pressed.
FROST Protection Mode
With the heater in any mode, OFF, MANUAL ON or AUTO, if the displayed
set temperature is reduced to 5
Protection mode - see Fig. 12. In this mode only, if the ambient temperature
drops below 5
o
C, will the heater come on. This is to prevent freezing.
In FROST Protection mode the heater comes on in the high heat mode
only. Pressing the ' ' button is the only way to bring the heater out of
this special mode.
Remote Control Operation - see Fig. 14
The batteries for the remote control are not installed in the remote but
are packed separately in the carton. To install batteries please follow
diagrams behind battery cover on the remote control.
The remote allows the set temperature to be adjusted, the mode to be
selected or can be used to put the heater in FROST Protection mode.
Full Heat output can only be achieved when using the remote control
i.e. both Left hand and Right hand panels are on.
Press the ' ' button on the Remote Control to go from OFF, Man
On High and back to OFF again. Press the ' ' or '
remote to set desired temperature between 5
button to put the heater into FROST Protection mode. Pressing the ' '
button (on the Remote Control) is the only way (using the Remote
Control) to bring the heater out of this mode i.e. pressing the ' ' or '
buttons on the remote will have no effect on the heater.
Discard leaking batteries
Dispose of batteries in the proper manner according to Provincial and
local regulations. Any battery may leak electrolyte if mixed with a different
battery type, if inserted incorrectly, if all the batteries are not replaced
at the same time, if disposed of in a fi re or if an attempt is made to
charge a battery not intended to be recharged.
s w i t c h O N a n d
o
C the heater will go into FROST
' buttons on the
o
o
C and 35
C. Press the '
Storage
If the radiator is not required for long periods, for example during the
summer, it should be stored in a dry place and preferably covered to
prevent the accumulation of dirt and dust. The plug and cord can be
stored in the storage area provided – see Fig. 15. The cord should be
neatly coiled around the hooks provided and the plug inserted into the
pin-hole in the central compartment.
Safety Overheat Protection
For your safety this appliance is fi tted with a thermal cut-out. In the
event that the product overheats for some reason, the cut-out prevents
excessive temperatures on the product by cutting the power to the
heater. Once the heater has cooled down, it will reset automatically, it
will continue to cycle on and off automatically until the reason for
overheating is removed.
Recycling
For electrical products sold within the European
Community.
At the end of the electrical products useful life it should
not be disposed of with household waste. Please recycle
where facilities exist. Check with your Local Authority or
retailer for recycling advice in your country.
Cleaning
WARNING - ALWAYS DISCONNECT THE POWER SUPPLY BEFORE
CLEANING THE HEATER.
Do not use detergents, abrasive cleaning powder or polish of any kind
on the body of the heater.
Allow the heater to cool, then wipe with a dry cloth to remove dust and
a damp cloth (not wet) to clean off stains. Be careful not to allow
moisture in to the heater.
After Sales Service
Your product is guaranteed for two years from the date of purchase.
Within this period, we undertake to repair or exchange this product
free of charge (excluding lamps & subject to availability) provided it
has been installed and operated in accordance with these instructions.
Your rights under this guarantee are additional to your statutory rights,
which in turn are not affected by this guarantee.
Should you require after sales information or assistance with this
product please contact Faber Internatiional, PO box 8440, AE
Heerenveer, T - 0513-656500
P l e a s e d o n o t r e t u r n a f a u l t y p r o d u c t t o u s i n t h e f i r s t
instance as this may result in loss or damage and delay in providing you
with a satisfactory service.
Please retain your receipt as proof of purchase.
'
'
- 5 -
Publicidad
