Fein ASCS4.8 Manual De Instrucciones página 18

OBJ_BUCH-0000000042-001.book Page 18 Wednesday, October 19, 2011 8:35 AM
en
18
Hand/arm vibrations
The vibration emission level given in this information
sheet has been measured in accordance with a standard-
ised test given in EN 60745 and may be used to compare
one tool with another. It may be used for a preliminary
assessment of exposure.
The declared vibration emission level represents the
main applications of the tool. However, if the tool is used
for different applications, with different accessories or
poorly maintained, the vibration emission may differ.
This may significantly increase the exposure level over
the total working period.
An estimation of the level of exposure to vibration
should also take into account the times when the tool is
switched off or when it is running but not actually doing
the job. This may significantly reduce the exposure level
over the total working period.
Identify additional safety measures to protect the opera-
tor from the effects of vibration such as: maintain the tool
and the accessories, keep the hands warm, organisation
of work patterns.
Operating instructions.
Adjust the rotation selector switch only when the
machine is at a complete stop.
To avoid accidental starting, e. g., during transport, set
the rotation selector switch to the centre position.
When overheated, the machine runs with short, low-
power impulses. Allow the machine to cool down at no-
load speed.
For reliable working results, always carry out screwdriv-
ing operations using the depth stop.
Electronic torque shut-off (see pages 6 – 7).
The electronic torque shut-off can be used when working
without depth stop.
Adjust the torque only when the machine is at a complete
stop.
The motor switches off when reaching the set torque and
an audio signal sounds. After the shut-off has taken place,
release the on/off switch and press it again for the next
screwdriving operation.
The audio signal can be switched on and off.
The electronic shut-off is deactivated when working in
the " " torque level.
To achieve good working results, press the power tool
with sufficient force against the screw.
Handling the battery.
Operate and charge the battery only within the battery
operating-temperature range of 0 °C – 45 °C (32 °F –
113 °F). At the beginning of the charging procedure, the
battery temperature must be within the battery operat-
ing-temperature range.
LED indicator Meaning
1 – 4 green Percentage of
LED charge condition
Continuous Battery is almost
red light empty
Red flashing Battery is not
light ready for opera-
tion
The real percentage of the battery charge condition is
only indicated when the power tool motor is stopped.
The electronics automatically switch off the motor prior
to the battery being deep discharged.
Repair and customer service.
When working metal under extreme operat-
ing conditions, it is possible for conductive
dust to settle in the interior of the power tool.
Blow out the interior of the power tool via the ventila-
tion slots frequently with dry and oil-free compressed air.
If required, you can change the following parts yourself:
application tools, depth stop, battery, belt clip
Warranty and liability.
The warranty for the product is valid in accordance with
the legal regulations in the country where it is marketed.
In addition, FEIN also provides a guarantee in accordance
with the FEIN manufacturer's warranty declaration.
The delivery scope of your power tool may include only
a part of the accessories described or shown in this
Instruction Manual.
Declaration of conformity.
FEIN declares itself solely responsible for this product
conforming with the relevant provisions given on the last
page of this Instruction Manual.
Technical documents at: C. & E. FEIN GmbH, EGZ,
D-73529 Schwäbisch Gmünd
Environmental protection, disposal.
Packaging, worn out power tools and accessories should
be sorted for environmental-friendly recycling.
Dispose of batteries only when discharged.
For batteries that are not completely discharged, insulate
the terminals with tape as a protective measure against
short-circuiting.
Activity
Operation
Charge battery
Bring the battery into
the battery operat-
ing-temperature
range, then charge