American Standard Prairie Field 8040.230 Serie Manual De Instrucciones

TISSUE HOLDER
SOPORTE PARA PAPEL HIGIÉNICO
SUPPORT DE PAPIER TOILETTE
Thank you for selecting American-Standard...the benchmark of fine
quality for over 100 years. To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
Gracias por seleccionar los productos American Standard, sinónimo de la mejor calidad
durante más de 100 años. Por favor lea estas instrucciones detenidamente antes de
comenzar para que lleve a cabo la instalación sin contratiempos.
Nous vous remercions d'avoir choisi American Standard... synonyme de qualité supérieure
depuis plus de 100 ans. Pour vous assurer que l'installation se déroulera sans difficulté,
veuillez lire attentivement ces instructions avant de commencer.
Recommended Tools & Materials/Herramientas y Materiales Recomendados/Outils et matériaux recommandés
10'
Tape Measure
Flexómetro
Ruban à mesurer
1
INSTALL MOUNTING PLATES
The TISSUE HOLDER (1) works best if secured to a wall stud or cross brace within the wall, using the SCREWS (3) supplied.
If the TISSUE HOLDER (1) is to be installed on a tile or plaster wall the ANCHORS (4) and SCREWS (3) should be used.
Note: The center line distance (6-1/4") between the MOUNTING PLATES (5) is critical, and must be maintained.
Determine desired height and location (optional) and mark a center line. Using the MOUNTING PLATE (5) as a template mark the two
spots for the mounting holes. If MOUNTING PLATE (5) is secured to a stud or cross brace drill small pilot holes for SCREWS (3).
For installations on drywall, use DRYWALL ANCHORS (6) and SCREWS (3) for securing MOUNTING PLATE (5) to wall. Place #2 Phillips
screwdriver or cordless screwdriver into recess of anchor. Press into drywall while turning the anchor clockwise until it is seated flush
with the wall. The TISSUE HOLDER BODIES (2) are mounted 6-1/4" center to center. Place MOUNTING PLATE (5) over DRYWALL
ANCHORS (6) and insert SCREWS (3) with #2 Phillips screwdriver. See illustration below. Repeat above steps for remaining
MOUNTING PLATES (5).
For installations on tiled walls, If TILE ANCHORS (4) and SCREWS (3) are used for securing MOUNTING PLATE (5), then drill
two 1/4" diameter holes a minimum of 1-1/4" deep. Insert the two TILE ANCHORS (4) flush with face of the finished wall. The TISSUE
HOLDER BODIES (2) are mounted 6-1/4" center to center. Place MOUNTING PLATE (5) over TILE ANCHORS (4) and insert screws
provided with #2 Phillips screwdriver. See illustration below. Repeat above steps for remaining MOUNTING PLATES (5).
Secure MOUNTING PLATE (5) to wall with SCREWS (3).
6-1/4"
6-1/4" (159 mm)
159 mm (6-1/4 po.)
4
6
5
3
6
4
Installation Instructions
Instrucciones de instalación
8040.230 SERIES
Drill
Taladro
Perceuse
CENTER LINE
LÍNEA CENTRAL
LIGNE CENTRALE
USE MOUNTING PLATE AS TEMPLATE
USE LA PLACA DE MONTAJE COMO PLANTILLA
UTILISER UNE PLAQUE DE MONTAGE COMME GUIDE
4
CENTER LINE
LÍNEA CENTRAL
LIGNE CENTRALE
Mode d'installation
SERIE 8040.230
SÉRIE 8040.230
Regular Screwdriver
Desarmador plano
Tournevis plat
1
3
5
FINISHED WALL
PARED TERMINADA
MUR FINI
Certified to comply with ANSI A112.18.1
Certificación de cumplimiento de la norma ANSI A112.18.1
Certifié conforme à ANSI A112.18.1
U.S. Patent No. D403,750
Patente estadounidense D403,750
Brevet U.S.A. no. D403,750
M 9 6 8 74 2 R E V. 1. 2
Phillips Screwdriver
Desarmador de cruz
Tournevis cruciforme
2