Auto Sleep - HK Audio ELEMENTS E 115 Sub D Manual De Instrucciones

Preset 1: 1x E 835 (2x E 435)
Preset 2: 2x E 835 (4x E 435)
Preset 3: 3x E 835 (6x E 435)
Heads up: You can combine the two models in a mixed confi guration, for
example, two E 835s and two E 435s. It this case, you would select Preset
3. You can even connect an odd number of E 435s, say, two E 835s and
one E 435s or three E 435s. In these cases, select the next lower preset
number and, if necessary, adjust the high frequencies using the mixer's
EQ or the frequency response using HK Audio DSP CONTROL software.
=
1x 2x
E 835 E 435
Preset Preset Preset Preset
1 1 1 2
Preset 4: Remote
This setting loads a user preset previously saved via the DSP CONTROL
application. The subwoofer does not need to be connected to the remote
software to do this.
You can save the following DSP functions via the remote DSP CONTROL
software as user presets – the fully parametric ten-band EQ with variable
fi lter characteristics for each frequency band, a high-pass and a low-pass
fi lter with variable fi lter characteristics, and limiter, delay, level and mute.
This screenshot shows the remote DSP CONTROL software. You can get this free application from the
ELEMENTS product download page at www.hkaudio.com.
●
9
Small Venue
We tuned your ELEMENTS system's frequency response for larger rooms,
which require speakers to throw sound over greater distances. When
setting the system up in smaller rooms, activate the Small Venue EQ with
this switch so the red LED lights up. This re-voices the system for it to
sound balanced and remarkably transparent even at very short range.
Preset Preset
2 3
●
10
Mid/High Out
Connect ELEMENTS mid/high units to this Speakon output via the EF 45
base (available as an accessory) or to forward their signal to an ELEMENTS
Install Kit.
Use standard cables equipped with Speakon NL2 connectors to this end.
Plug in the Speakon cable and turn the connector clockwise to lock it in
place. Be sure to fi rst turn the connector counterclockwise to unlock it
before unplugging it.
Heads up: Mid/High Out is wired in parallel to the E-Connect (15) signal
bus on top of the E 115 Sub D. Use this output only when the E-Connect
bus is not in use.
Heads up: Connecting any component other than ELEMENTS mid/high
units to this Speakon output may damage it and destroy the subwoofer's
electronics.
●
11
Mains Input
Use the factory-included Powercon mains cord to connect this socket to a
power outlet. Insert the push-pull connector and turn it clockwise to make
sure the Powercon cord engages and locks. To unlock it, pull the Powercon
plug's locking mechanism towards the cable and turn it counterclockwise.
●
12
Power
This rocker switch turns the power on and off . Set it to Power to turn the
electronic components on and to Off to disconnect them from the mains
power supply.
●
13
Power-LED
This LED lights up green when the electronic components are getting mains
power.
●
14

Auto Sleep

Use this recessed button to switch energy-saving Auto Sleep mode on and
off . Your speaker leaves the factory with the Auto Sleep button pressed to
enable this mode. This function puts the electronic components to sleep
when four and a half hours pass without the speaker registering an audio
signal, data sent to the Ethercon ports, or an adjustment of a button or
knob. The only way to wake it up is by switching the Power button off and
on again or patching an analog audio signal into the Input.
●
15
E-Connect
The dual-purpose ELEMENTS E-Connect output/coupler is located on the
top of the E 115 Sub D enclosure. Use it to connect E 835 and E 435 mid/
high units and the EP 1 and EP 2 speaker extension poles. The subwoofer
can drive up to three E 835 mid/high units or up to six E 435s. For more on
this, see section 3, Setting Up and Connecting the Column's components.
Heads up: The E-Connect bus is wired in parallel to the Mid/High Output
on the rear panel (Speakon). Use it only when the Speakon Out port is not
in use.
ELEMENTS E 115 Sub D 1.1
5