Function Of The Integral Uv System In The Aqa Drink Pro 20; Aqa Drink Pro 20 Cabinet (Optional); Operating And Safety Instructions - BWT AQA DRINK PRO 20 HCS Instrucciones De Montaje Y Manejo

The rear panel of the AQA drink Pro 20 HCS water dispenser has the following connections (fig. 5):
4
5
Fig. 5: Rear panel of the AQA drink Pro 20 HCS
The rear panel of the AQA drink Pro 20 HCA water dispenser has the following connections (fig. 6):
4
EN
Fig. 6: Rear panel of the AQA drink Pro 20 HCA

3.3 FUNCTION OF THE INTEGRAL UV SYSTEM IN THE AQA DRINK PRO 20

The AQA drink Pro 20 water dispenser has an integrated UV system with a lamp output of 11 watts.
When the UV lamp is in operation, the LED indicator on the front of the control panel lights up. If a
button is pressed for water, the water is dispensed after about 2 seconds of UV sterilisation. If the
water dispensing function does not start, press the water dispensing button once more. After each
time water is dispensed, UV sterilisation continues for approximately 60 seconds.
Note!
If the UV lamp is defective or is not connected, water can still be freely dispensed without re-
strictions. However, an acoustic warning signal sounds when the selection buttons are pressed
and the LED indicator on the operator panel flashes.
According to disinfection requirements the UV lamp might light up for longer than the nominal
60 sec. which might heat up the water in the reactor significantly. When this is observed just
flush till nominal temperature is restored.
26
1. On/off switch for the boiler (HOT)
2. On/off switch for the carbonator pump
(CO )
2
3. Power connection
4. CO connection (CO INLET)
2 2
5. Water connection (WATER INLET)
6. Hot water discharge (DRAINAGE)
1
2
3
6
1. On/off switch for the cooling function
(COLD)
2. On-off switch for the boiler (HOT)
3. Power connection
4. Water connection (WATER INLET)
5. Hot water discharge (DRAINAGE)
1
2
3
5

3.4 AQA DRINK PRO 20 CABINET (OPTIONAL)

The AQA drink Pro 20 water dispenser (fig. 7) is also available with an optional cabinet for install-
ing the water dispenser as a free-standing unit. The cabinet has height-adjustable feet on the
underside and an integrated cup dispenser on the front. A wastewater tank with a wastewater
level sensor is connected to the upper section inside the cabinet (fig. 8 and fig. 9). The cable for
the level sensor in the cabinet is connected to the plug on the left-hand side of the base plate of
the water dispenser.
The scope of supply for the cabinet comprises:
» Integrated wastewater tank (3 l)
» Drip tray holder
Fig. 7: AQA drink Pro 20 Fig. 8: Interior of the AQA
cabinet (external view) drink Pro 20 cabinet with
wastewater tank in place

4. OPERATING AND SAFETY INSTRUCTIONS

These installation and operation instructions contain important information concerning the safe
and efficient use of the AQA drink Pro 20 water dispenser. Despite all safety precautions, there
remain residual hazards with every product, especially if it is not handled properly. Every techni-
cal device requires regular maintenance and servicing (Chapter 6) to work properly. Compliance
with all safety and handling instructions provided is a fundamental requirement for safe opera-
tion. In addition, the local accident prevention regulations and general safety regulations valid
at the location of the device apply.
Danger due to electricity!
Before performing maintenance work on this device, it must be disconnected from the mains
supply.
It must be possible to disconnect the electric current either by pulling out the power cable or
by means of a biploar mains switch at the socket.
If the power cable is damaged, it must be replaced by the manufacturer or a qualified
technician.
Do not use extension cables or multiple adapters.
Fig. 9: Interior of the AQA
drink Pro 20 cabinet without
wastewater tank in place
EN
27