Rear Panel; Operation - Omnitronic CM-742 Manual Del Usuario

5.2 Rearpanel
CAUTION
Read manual before use.
To prevent electrical fire and shock hazard, do not expose this appliance
to moisture. Risk of electric shock! Do not open! Disconnect from mains
before changing fuse. Replace the fuse only with the same type and rating.
Vor Gebrauch Anleitung lesen.
Gerät vor Feuchtigkeit schützen. Bei Sicherungswechsel Netzstecker ziehen!
Gefahr! Gerät nicht öffnen! Nur Sicherungen mit gleichen Leistungswerten einsetzen.
Lire le mode d'emploi avant l'utilisation.
Afin de prévenir tous risques d'électrocution et de court-circuits, ne pas exposer
VOLTAGE SELECTOR
à l'humidité. Attention! Ne pas ouvrir le boîtier!
Utiliser un fusible de rechange de même type.
AC INPUT 115/230 V
FUSE F 0.5 A, 250 V
Typ/Type:
Spannungsversorgung/Power supply:
115/230 V AC, 50/60 Hz ~
Gesamtanschlusswert/Power
consumption:
230
Sicherung/Fuse:
OMNITRONIC SHOWEQUIPMENT GmbH, GERMANY
49 48 47
(33) X-START-SOCKETS
Via the Start-socket, the respective CD-player can be remotely controlled via the Crossfader. If you are using
a CD-player with Faderstart-function connect the mixer with the Control-socket. Please note that these
sockets must never be connected with any voltage.
(34) GND (Ground terminal)
Connect the ground lead of the turntable with this terminal. This helps to reduce humming and pop noises.
(35) PHONO / AUX-SELECTOR
Used to switch the input sockets of CH-1, CH-2 and CH-3 to Phono or Aux.
(36) MIC 2-SOCKET
Connect your microphone with ¼" jack plug here. The signals can be controlled via CHANNEL 4, if the MIC 2
/ LINE 4-switch is set to MIC 2.
(37), (38), (39), (40) LINE / PHONO / AUX INPUT-SOCKETS
Input socket for CH-1, CH-2, CH-3 and CH-4. Connect turntables equipped with MM pickup cartridge to
PHONO input. CD players or Tape Decks should be connected to LINE input. Line level musical instruments
with stereo outputs such as Rhythm Machines or Samplers should also be connected to LINE inputs.
(41) EFFECTS SEND/RECEIVE-SOCKETS
To connect your sound effectors here.
(42) REC OUT
To connect your recording unit.
(43) MASTER 1 OUT
Output sockets for connecting your power amplifier.
(44) MASTER 2 OUT
Output sockets for connecting your power amplifier.
(45) BOOTH
Connect your monitor system here.
(46) MASTER 1 BALANCED OUTPUT
Balanced output for the master 1 signal.
(47) FUSEHOLDER
Only replace the fuse when the device is disconnected from mains. Only use fuses of the same rating and
power.
(48) AC-CONNECTION
Used to plug the power cord in.
(49) AC VOLTAGE-SELECTOR
Make sure that the selector is properly set.

6. OPERATION

Switch the device on via the power switch.
As soon as the Audio-signals are present the signal level is displayed. You can adjust the level of the input
signals via the Gain-control.
!
Débrancher avant de remplacer le fusible.
OMNITRONIC CM-742
18 W
F 0,5 A, 250 V
RIGHT LEFT
MASTER 1 BALANCED OUTPUT
46
33
®
PLAYER CONTROL
A
B
BOOTH MASTER 2 MASTER 1 REC SEND RECEIVE
L
R
OUTPUT EFFECTS
45 44 43 42 41
21
34 35
www.omnitronic.com
GND AUX 3 PHONO 3 AUX 2 PHONO 2 AUX 1 PHONO 1
PHONO 3 PHONO 2 PHONO 1
LINE 4 LINE 3 LINE 2 LINE 1
AUX 3 AUX 2 AUX 1
CH-4 CH-3 CH-2 CH-1
40 39 38 37
MIC 2
36