Kenwood FPM90 Manual De Instrucciones página 14

slicing/grating discs
slicing discs - 4mm
Use the slicing side for cheese, carrots, potatoes, cabbage,
cucumber, courgette, beetroot and onions.
grating discs - 4mm
Use the grating side for cheese, carrots, potatoes and foods
of a similar texture.
extra fine grater disc
Grates Parmesan cheese and potatoes for German potato
dumplings.
dn
fine julienne (if supplied)
Use to cut potatoes into straws and coarse grate for rosti,
stir fries and vegetable garnishes.
decorative slicing disc
Use to slice potatoes, carrot, cucumbers and foods of a
similar texture into fluted shaped slices.
dp
French fry disc (if supplied)
Cuts potatoes for thin French Fries and ingredients for
casseroles and dips (eg cucumber, apple and pear.)
safety
Never remove the lid until the cutting disc has
G
completely stopped.
Handle the cutting discs with care - they are
G
extremely sharp.
Do not overfill the bowl – do not exceed the
G
maximum capacity level marked on the bowl.
to use the cutting discs
1 Fit the detachable drive shaft and bowl onto the power unit..
2 Holding by the centre grip, place the disc onto the drive shaft
with the appropriate side uppermost
3 Fit the lid.
4 Put the food in the feed tube.
Choose which size feed tube you want to use. The pusher
contains a smaller feed tube for processing individual items
or thin food items.
To use the small feed tube – first put the large pusher inside
the feed tube.
To use the wide feed tube – fit the small pusher into the
wide pusher and turn clockwise to lock in place.
Do not fill the feed tube above the maximum level as the
processor will not operate unless the wide feed tube pusher
is fitted correctly.
5 Switch on and push down evenly with the pusher - never
put your fingers in the feed tube.
hints
Use fresh ingredients
G
Don't cut food too small. Fill the width of the feed tube fairly
G
full. This prevents the food from slipping sideways during
processing. Alternatively use the small feed tube.
When using the Julienne disc, place ingredients horizontally.
G
When slicing or grating: food placed upright
G
shorter than food placed horizontally
G Food placed upright comes out shorter than food placed
horizontal.
There will always be a small amount of waste on the disc or
G
in the bowl after processing.
cr cs
, 2mm
ct dk
, 2mm
dm
(if supplied)
do
(if supplied)
bm
.
bn
comes out
bo
.
dq
mini bowl and knife
Use the mini processor bowl to chop herbs and process
small quantities of ingredients e.g. meat, onion, nuts,
mayonnaise, vegetables, purées, sauces and baby food.
Do not overfill the bowl.
a mini blade
b mini bowl
to use the mini bowl and knife
1 Fit the detachable drive shaft and bowl onto the power unit.
2 Fit the mini bowl over the detachable drive shaft - ensure the
cut out sections align with the locating tabs
bowl.
Note: The main bowl lid cannot be fitted if the mini bowl is
not located correctly.
3 Place the knife blade over the drive shaft
4 Add the ingredients to be processed.
5 Fit the lid and switch on.
safety
Never remove the lid until the knife blade has completely
G
stopped.
The knife blade is very sharp - always handle with care.
G
important
Do not process spices – they may damage the plastic.
G
Do not process hard food such as coffee beans, ice cubes
G
or chocolate – they may damage the blade.
hints
Herbs are best chopped when clean and dry.
G
Always add a little liquid when blending cooked ingredients
G
to make baby food.
Cut foods such as meat, bread, vegetables into cubes
G
approximately 1-2 cm (
When making mayonnaise add the oil down the feed tube.
G
dr
compact chopper/grinder
Use the compact chopper/grinder for processing dry
ingredients such as nuts, coffee beans and it is also suitable
for processing a range of spices such as: -
Black peppercorns, cardamom seeds, cumin seeds,
coriander seeds, fennel seeds, fresh ginger root, fresh
chillies and whole cloves.
a sealing ring
b blade unit
c glass jar
to use your compact chopper/grinder
1 Put your ingredients into the jar. Fill it no more than half full.
2 Fit the sealing ring to the blade unit.
3 Hold the underside of the blade unit and insert the blades
into the jar – turn anti-clockwise to lock
4 Place the compact chopper/grinder onto the power unit and
turn clockwise to lock
5 Use the Auto button, or select a speed (refer to the
recommended speed chart).
12
(if supplied)
bp
on the main
bq
.
1 ⁄ – 3 ⁄ in) before processing.
2 4
(if supplied)
br
.
bs
.