Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
NE 5007
ASSEMBLY INSTRUCTIONS
STOP:
THIS IS NOT A COMPLETE PLAN. FOLLOW THE PROJECT 613
ASSEMBLY PLAN UP TO PAGE 46, OMITTING THE SLIDE
INSTALLATION.
32'
29'
No. of Children: Up to 12
Min. Use Zone: 32 ' x 29 '
Set Dim. 20 'W x 10 'L x 13'H
Est. Building Time: 5-10 hr.
To register your product visit:
http://www.swing-n-slide.com
Other benefits include information on product warranties, assembly plan updates, joining our mailing
list for new products and promotions, receiving our newsletter, and providing feedback on products.
Swing•N•Slide • 1212 Barberry Drive • Janesville, Wisconsin 53545
Visit our web site at: www.swing-n-slide.com or call us at
1-800-888-1232
Publicidad
Tabla de contenido
Manuales relacionados para Swing-N-Slide NE 5007
Resumen de contenidos para Swing-N-Slide NE 5007
- Página 1 Other benefits include information on product warranties, assembly plan updates, joining our mailing list for new products and promotions, receiving our newsletter, and providing feedback on products. Swing•N•Slide • 1212 Barberry Drive • Janesville, Wisconsin 53545 Visit our web site at: www.swing-n-slide.com or call us at 1-800-888-1232...
-
Página 2: Disposal Instructions
When the equipment is taken out of service, it must be disassembled and disposed of in such a way that no unreasonable hazards will exist at the time the set is discarded. Important! Additional Safety Instructions for all Swing-N-Slide Playground Equipment. Save this instruction sheet in the event the manufacturer needs to be contacted. - Página 3 Swing-N-Slide® will repair, or at its discretion, replace any part within the stated warranty period which is defective in workmanship or materials. This decision is subject to verification of the defect upon delivery of the defective part to Swing-N-Slide® at 1212 Barberry Drive, Janesville, Wisconsin, 53545. Any part(s) returned to Swing-N- Slide®...
- Página 4 PROJECT 615 ALPINE 615 PROJECT LUMBER LIST THIS LIST IS IN ADDITION TO LUMBER REQUIRED BY PROJECT 613 (3) 2'' x 4'' x 8' (2) 2'' x 4'' x 10' (3) 5/4'' x 6'' x 10' ALPINE ROCK WALL LUMBER 55-1/4'' 23-1/4'' (1) 2'' x 4'' x 96''...
- Página 5 PROJECT 615 How to select the correct fastener Use these 3 pictorial guides to help select the correct fastener(s) for the lumber attachment you are making. Each diagram will highlight the correct number of fasteners to use, and where to attach them. 5/4"...
- Página 6 PROJECT 615 Fig. 1 FLUSH 2-1/2" screws Fig. 1a 2-1/2" screw FLUSH (4) 2-1/2" screws Rock Wall Support 1. Assemble the Rock Wall Support as shown in (Fig. 1). 2. Install the Rock Wall Support as shown in (Fig. 1a). FLUSH 2-1/2"...
- Página 7 PROJECT 615 Fig. 2 (11) 5/4 x 6 x 30 po FLUSH (3,2 x 10,2 x 76,2 cm) 2-1/2" screws (Per joint) 3-3/8" 3-3/8" 2-1/2" screw NOTE: Fig. 2a 5' Climbing Rock Wall will require UNDER DECK VIEW 12 Climbing Rocks (3) Bags of Climbing Rocks.
- Página 8 PROJECT 615 Climbing Rock Fig. 3 (2) “T” nuts 3/8" Holes (2) 2" Hex Head Bolts Hold (rock) (1) Loc Washer per bolt (1) Flat Washer per bolt Climbing Rock Installation 1. Mark locations of Climbing Rocks on the Climbing Wall in a pattern that will easily allow your child to climb to the deck.
- Página 9 PROJECT 615 Fig. 4 Fig. 4a 2-1/2" screw Slide Barrier Construction 2-7/8" Gap Between Each 1. Carefully remove your Barrier Support Board and Barrier Board (6) Barrier Boards from the back barrier to place your slide, as shown in (Fig. 4). Retain this lumber and fasteners as you will need them in the next step.
- Página 10 PROJECT 615 Fig. 5 2-1/2" screws per joint Fig. 5a 2-1/2" screws per joint 2-1/2" screw Slide Barrier Construction 2-1/2" screws 1. Attach the Turbo Tube Slide Support Board as shown in (Fig. 5) and (Fig. 5a). 2-1/2" screws...
- Página 11 PROJECT 615 Fig. 6 2-1/2" screws per board INSIDE VIEW OF SLIDE ENTRANCE 2-1/2" screw Slide Barrier Construction 1. Install interior slide barrier support boards shown in (Fig. 6). 2. Refer to the 5’ Turbo Tube Slide Plan for instructions on assembling the Turbo Tube Slide and Footer Assembly.
- Página 12 REFERENCE THE PLAN PICTURED FOR SLIDE ASSEMBLY...
-
Página 13: Instrucciones De Ensamblaje
Swing•N•Slide • 1212 Barberry Drive • Janesville, Wisconsin 53545 Visite nuestro sitio web en www.swing-n-slide.com o llámenos al Visitez notre site Web au www.swing-n-slide.com ou appelez-nous au... - Página 14 Lorsque l’équipement est mis hors service, il doit être démonté et conditionné de sorte qu’aucun danger justifié ne sera présent lors de la mise au rebut de l’ensemble. Important! Instructions supplémentaires de sécurité pour tous les centres de jeu Swing-N-Slide. Conserver ce feuillet d’instruction au cas où vous devriez prendre contact avec le fabricant.
- Página 15 PROJECT 615...
- Página 16 LISTE DU BOIS D’ŒUVRE POUR LE PROJET ALPINE 615 CETTE LISTE S’AJOUTE À CELLE DU BOIS D’ŒUVRE POUR LE PROJET ALPINE 614 LISTA DE MADERA DEL PROYECTO 615 DE ALPINE ESTA LISTA ES ADICIONAL A LAS TABLAS REQUERIDAS PARA EL PROYECTO 613 (3) 2 po x 4 po x 8 pi (5,1 x 10,2 x 243,8 cm) (2) 2 po x 4 po x 10 pi (5,1 x 10,2 x 304,8 cm) (3) 5/4 po x 6 po x 10 pi (3,2 x 15,2 x 304,8 cm)
-
Página 17: Tire-Fonds De 2 Po (5,1 Cm)
PROJECT 615 Comment sélectionner la bonne fixation Utilisez ces trois guides illustrés pour vous aider ą sélectionner la (les) bonne(s) fixation(s) pour fixer l’assemblage de bois en cours. Chaque diagramme présente le nombre de fixations ą utiliser adéquat et l’emplacement approprié pour la fixation. 5/4 x 6 po aux 4 x 4 po (3,2 x 15,2 cm aux 10,2 x 10,2 cm) Vis de 2-1/2 po (6,4 cm) Posez les vis de 2-1/2 po (6,4 cm) pour fixer solidement les... - Página 18 PROJET 615/PROYECTO 615 Fig. 1 À RAS AL RAS (2) 2 tornillos de 2-1/2 po (6,35 cm) Fig. 1a À RAS Vis de 2-1/2 po (6,4 cm) AL RAS Tornillo de 2-1/2 po (6,4 cm) Support du mur d’escalade à rochers 1.
-
Página 19: Rocas Para Escalar
PROJET 615/PROYECTO 615 PROJECT 615 Fig. 2 (11) 5/4x 6 x 30 po À RAS (3,3 cm x 15,3 cm x 76,2 cm) AL RAS (2) Vis de 2-1/2 po REMARQUE : (6,4 cm) (par joint)) Le murs d’escalade à rochers de (2) Tornillos de 2-1/2 po (6,4 cm) 60 po (152,4 cm) nécessitera... - Página 20 PROJET 615/PROYECTO 615 Fig. 3 (2) Tuercas en “T” (2) Écrous en (2) pernos con cabeza « T » hexagonal de 1/2 po (13 mm) (2) Boulons à tête hexagonale de 1/2 po (13 mm) Agujeros de 3/8 po (9,5 mm) Trous de 3/8 po (9,5 mm) sostén (piedra) Prise (rocher)
- Página 21 PROJET 615/PROYECTO 615 PROJECT 615 Fig. 4 Construction de la barrière de glissade 1. Retirez avec précaution la planche de support de la barrière et les (6) planches de barrière de la barrière arrière pour pouvoir installer la glissade comme illustré dans la (Fig.
- Página 22 PROJET 615/PROYECTO 615 Fig. 5 (3) Vis de 2-1/2 po (6,4 cm) par joint (3) Tornillos de 2-1/2 po (6,4 cm) por cada junta (3) Vis de 2-1/2 po Fig. 5a (6,4 cm) par joint (3) Tornillos de 2-1/2 po (6,4 cm) por cada junta Vis de 2-1/2 po (6,4 cm) Tornillo de 2-1/2 po (6,4 cm)
-
Página 23: Vista Interior De La Entrada Del Tobogán
PROJET 615/PROYECTO 615 PROJECT 615 Fig. 6 (4) Vis de 2-1/2 po (6,4 cm) par planche (4) Tornillos de 2-1/2 po (6,4 cm) por cada tabla VUE DE L’INTÉRIEUR DE L’ENTRÉE DE LA GLISSADE VISTA INTERIOR DE LA ENTRADA DEL TOBOGÁN Vis de 2-1/2 po (6,4 cm) Tornillo de 2-1/2 po (6,4 cm) Construction de la barrière de glissade... - Página 24 Swing-N-Slide • 1212 Barberry Drive • Janesville, Wisconsin 53545 Visite nuestro sitio Web en: www,swing-n-slide.com o llámenos al Consultez notre site Internet à l’adresse suivante : www.swing-n-slide.com ou telephonez-nous au 1-800-888-1232 Swing-N-Slide 2015 LA 7490 Impreso en China/Imprimé...