Cleaning And Maintenance - ulsonix AIRCLEAN 600B Manual De Instrucciones

EN
3.1. DEVICE DESCRIPTION
AIRCLEAN 600P
1
2
3
1. Fan
2. Remote control
3. Display
6 8
4
5
7 9
4. „POWER" button
5. „REMIDER RESET" button
6. „AWAY MODE" button
7. „NORMAL/HIGH" button
8. Button increasing the air-flow speed (FAN )
9. Button decreasing the air-flow speed (FAN )
10. Button increasing the ozonation level (STERILZE
11. Button decreasing the ozonation level (STERILZE
)
15
14
16
17
13
12
12. Power switch
13. Connecting the power cord
14. UV lamp
15. Back cover
16. 3-in-1 filter (pre-filter, carbon filter, catalytic filter)
17. Ceramic ozone plate
10
AIRCLEAN 600B
D
B
C
A
A. „ON/OFF" button
B. „OZONE" button
C. Timer
D. Fan
10
I
11
H
)
E. Back cover
F. 3-in-1 filter (pre-filter, carbon filter, catalytic filter)
G. Ceramic ozone plate
H. UV lamp
I. Ozone plate placement
3.2. PREPARING FOR USE
APPLIANCE LOCATION
The temperature of environment must not be higher than
40°C and the relative humidity should be less than 85%.
Ensure good ventilation in the room in which the device
is being used. There should be at least 10 cm distance
between each side of the device and the wall or other
objects. Keep the product away from hot surfaces. The
device should always be used when positioned on an
even, stable, clean, fireproof and dry surface, and be out
of the reach of children and persons with limited mental
and sensory functions. Position the device such that you
always have access to the power plug. The power cord
connected to the appliance must be properly grounded
and correspond to the technical details on the product
label.
20.08.2020
ASSEMBLING THE DEVICE
The correct installation of the filter is shown in the figure
below.
3.3. DEVICE USE
AIRCLEAN 600P
1. Connect the device to the power supply.
2. Turn the device on with the power switch. Then press
the "POWER" button.
3. Set the appropriate parameters:
a) Mode selection:
» "NORMAL" mode - the UV lamp and catalytic
filter are turned on. A blue light on the front of
the device will switch on. CAUTION! You must not
look directly at the blue light.
E
» "HIGH" mode - UV lamp and ozonation
("STERILZE") will be turned on.
b) Adjustment of parameters
Adjust using the "STERILZE △" and "STERILZE ▽"
• SETTING THE OZONATION LEVEL
F
buttons. It is recommended to select the ozonation
level depending on the area (12 levels): 1 m
- 70 m - 93 m
2
- 209 m - 232 m
2
Adjust with the "Fan △" or "Fan ▽" buttons (5 levels).
G
• SETTING THE AIR-FLOW SPEED
• OZONATION WITH A TIMER
In order to activate ozonation in time mode, press the
"AWAY MODE" button and then set the time (1, 2, 4, 6,
8, 10 or 12 hours) of the device operation. The device
turns off automatically.
4. After use, switch the device off and disconnect from
the power supply.
CAUTION! The icon
filter by "blinking". After replacing the filter, reset the
filter condition by pressing and holding the "REMIDER
RESET" button on the panel for 10 seconds until the
icon disappears.
CAUTION! The device can be controlled using the
control panel or the remote control. The remote
control has additional functions: "APCO" - turns the
UV lamp on/off and the "Plasma" button - turns the
ion functions on/off.
AIRCLEAN 600B
1. Connect the device to the power supply.
2. Turn the device on with the power switch.
3. Press the "ON/OFF" button (After turning the device
on, the fan, ionizer, UV lamp and ozonator at level
I will turn on automatically).
4. Enter the settings:
• The timer can be set to 2, 4, 6 or 8 hours.
• The ozonator intensity can be adjusted with the
"OZONE" button (4 levels). The ozonation function
will automatically turn off after one hour if the timer is
not set.
CAUTION: The ionizer works regardless of the
20.08.2020
11 EN
ozonator.
5. After use, switch the device off and disconnect from
the power supply.
NOTE! Upon completion of treatment ventilate the
room for 15 to 30 minutes. Do not enter the room
for at least 2 hours after completion of the ozone
treatment.
NOTE ! Ozone is an irritant gas, it may cause damage
to biological membranes through radical reactions
with their constituents. If the characteristic ozone
smell is still present in the room which was treated
with ozone, first make sure that the device is switched
off then leave the room and/or ventilate it.
3.3.1. RECOMMENDED WORKING TIME
Recommended working time [min] depending on the
room volume [m
m
3
min
NOTE! Do not exceed the "Recommended operation
duration" as indicated in the above tables.

3.4. CLEANING AND MAINTENANCE

a) Always unplug the device before cleaning it.
b) Use only non-corrosive cleaners to clean the surface.
c) After cleaning the device, all parts should be dried
completely before using it again.
- 46 m d) Store the unit in a dry, cool place, free from moisture
2 2
and direct exposure to sunlight.
- 116 m - 139 m - 163 m - 186 m
2 2 2 2 2
e) Do not spray the device with a water jet or submerge
- 255 m - 279 m >.
2 2 2
it in water.
f) Do not allow water to get inside the device through
vents in the housing of the device.
g) The device must be regularly inspected to check its
technical efficiency and spot any damage.
h) Use a soft, damp cloth for cleaning.
i) Do not use sharp and/or metal objects for cleaning
(e.g. a wire brush or a metal spatula) because they
may damage the surface material of the appliance.
j) When the purifier no longer produces enough ozone,
informs about changing the
clean the ozone plate of dust with a soft cloth. It is
recommended to replace the ozone plate every 6
months.
DISPOSING OF USED DEVICES
Do not dispose of this device in municipal waste systems.
Hand it over to an electric and electrical device recycling
and collection point. Check the symbol on the product,
instruction manual and packaging. The plastics used to
construct the device can be recycled in accordance with their
markings. By choosing to recycle you are making a significant
contribution to the protection of our environment. Contact
local authorities for information on your local recycling
facility.
]
3
50 100 150 200 300
60 120 180 240 360