Before Use - Taurus 948050 Manual De Instrucciones

ing parts/accessories.
2.4.2. If the power cord is damaged, the manu-
facturer or its service agent or a similarly qualified
person must
replace it in order to avoid a hazard.
2.4.3. Any misuse or failure to follow the instruc-
tions for use renders the guarantee and the manufac-
turer's liability null and void.
3. Instructions for use

3.1. Before use:

IMPORTANT: Please remember that your steam
cleaner operates by emitting steam at an increased
temperature of 115°C. Always test on an inconspicu-
ous area first. Never use it on objects or surfaces
which cannot resist this temperature, or on surfaces
with coatings or polishes, or on delicate materials
such as dralon, plastic, natural fur or antique items
etc. If in doubt, check carefully on a part of the
material where minor marks will not matter.
3.2. Use and care:
3.2.2. Upright steaming - Assembly
3.2.2.1. Insert the handle onto the main body.
3.2.2.2. Insert one of the screws (supplied) into the
hole in the lower cord storage hook and rotate until
tight.
3.2.2.3. Insert the other screw (supplied) into the
side of the handle (on theopposite side to the lower
cord storage hook) and rotate until tight.
NOTE: Attaching the handle is necessary for first
time assembly only.
3.2.2.4. Lower the main body onto the floorhead
(18), with the floorhead release button on the neck
of the floorhead to the back of the assembly, until it
clicks into place.
3.2.2.5. Insert the steam outlet nozzle at the bottom
end of the hand-held steamer into the adaptor at the
bottom of the space in the front of the main body.
Push the steam cleaner firmly into the space in the
main body until it clicks into place.
3.2.2.6. Attach the floor cloth (20) to the floorhead
and tighten the toggle at the rear.
3.2.3. Using in upright steam mode
IMPORTANT: Before use, hardfloors should be
thoroughly swept and carpets should be
thoroughly dry vacuumed. However, we recommend
948050_IM.indd 4
that your steam cleaner is not used on:
•bare wooden floors or any surfaces where wood is
exposed (as it will absorb moisture and may distort).
•damaged hardfloors or hardfloors with gaps pres-
ent (as it will absorb moisture and may distort).
Also, do not keep your steam cleaner in one place
for an extended period, because the continual
heat may cause damage to carpets and laminate
flooring.
Please disconnect and allow the unit to cool before
changing cloths and attachments.
3.2.3.1. Squeeze the buttons (on the side of the
water tank to remove it from the handheld steam
cleaner. Remove the filler cap by lifting it out.Fill the
watertank.
IMPORTANT: To prevent limescale build-up in the
water tank, never fill your steam cleaner's tank with
anything other than deionised, demineralised or
distilled water (available from most leading super
markets). Any problems arising from limescale will
invalidate the product warranty.
Replace the filler cap and insert it into place
Replace the water tank.
3.2.3.2. Attach the microfibre floor cloth to the
floor head, with the blue side of the cloth
facing the floor.
3.2.3.3. Plug in at the mains outlet and switch on the
steam cleaner by pressing the on/off power switch.
The power indicator light will illuminate
and steam will be ready to be emitted after around
30 seconds (when the steam trigger is pressed).
3.2.3.4. WARNING: Before switching ON, ensure
the floorhead is located safely away from persons or
animals.
3.2.3.5. Place the big triangle floor head on the floor.
Hold the floorhead to the floor with your foot and
tilt the main body back.Squeeze the steam trig-
ger to release steam from the floor head. This will
take a few seconds. Only operate the steam trigger
intermittently to avoid overaturation of the cloth and
floor. The head and moisture in the cloth should
easily clean the floor. Excess steam will result in the
floor taking longer to dry. Keep the floor head moving
whilst cleaning.
Never hold the cleaner in one spot for an extended
period.
19-Jul-17 7:26:26 AM