Panasonic CZ-256ESMC3 Manual Del Usuario página 4

Preparations for Wiring
 Power Supply Wiring
• Be sure to use a dedicated line for power source.
• Be sure to earth this controller.
• Do not connect the earth wiring to those of gas pipe, water
pipe, lighting rod, telephone, etc.
 Type of wiring
• Use a fl exible wiring of 2 mm
• Use the standard power supply wiring for Europe (such as
H05RN-F or H07RN-F which conform to CENELEC (HAR)
rating specifi cations) or use the wiring based on IEC
standard (60245 IEC57, 60245 IEC66).
 Total Wire Length : 30 m or less
 Inter-Unit Control Wiring
 Type of wiring
• Use a fl exible shield wiring of 0.5 to 2 mm
• No polarity
 Total Wire Length : 1000 m or less
 Number of connectable units and devices :
(→ P.2 "Specifi cations")
Attention
• Ground the shield on both sides of shield wiring, otherwise an
operation error from noise may occur.
Wiring
Basic Wiring Diagram
N
L
Power source (100-240 V~ 50/60 Hz)
This unit
Power supply
wiring
L
N
Outdoor unit
U1 U2
+
–
Communication
Adaptor
U1 U2
Indoor unit
1. Turn the circuit breaker off before connecting the wiring
2. How to Attach the Ring Pressure Terminal
 For power supply wiring
Process the end of each wiring, and
attach the ring pressure terminal (fi eld
supplied item).
 For shield wiring
Process the end of the each wiring and attach the ring
pressure terminal (fi eld supplied item).
Remove wiring coat.

Cover with the tape.

Attach ring pressure

terminal.
3. Remove the
power switch
Power switch cover
cover
2 (Recommended).
.
2
Outdoor
unit
U1
+
U1 U2
U2
–
Inter-unit control
Communication
wiring
Adaptor
control wiring • No polarity
• Polarity
present
U1 U2 U1 U2
Indoor unit Indoor unit
1-1 1-2
Strip
Shield mesh
Strip
Insulation tape
Shield mesh
Ring pressure
terminal
Power-in port
Screw
 Communication Adaptor Control Wiring
(When connecting a Communication Adaptor)
 Polarity (+/-) present
 Number of connectable Communication Adaptor: up to 7 units
 For the type of wiring and total wiring length,
see "Installation Instructions" supplied with the
Communication Adaptor.
 External I/O Wiring
(When connecting external equipment)
 Type of wiring
• Use a fl exible wiring of 0.5 to 2 mm
 Wire Length : 20 m or less
Attention
• When using the controller at a location susceptible to noise,
use a shield wiring.
 LAN Cable
 Type of wiring
• Category 5 or above straight cable
 Wire Length : 100 m or less
Ground
4. Wiring
Connect the power supply wiring.

 Connect the power supply wiring and the earth wiring to
the power supply terminal board and the earth terminal
board (on the sheet metal case) respectively.
*3
*3: Use earth terminal board as protective earth
• Do not over-tighten. (The screw may be damaged.)
Connect the inter-unit control wiring.

 Connect the shield part of the shield wiring to No. 0 (FG
of the signal terminal board (TB2).
*4: Functional Ground
• Do not over-tighten. (The screw may be damaged.)
 There is no polarity.
Connect the Communication Adaptor control wiring.

 Make sure the polarities (+/-) are correct.
Attention
• Read the "Installation Instructions" supplied with the
Communication Adaptor.
Connecting external equipment.

Attention
Ring
• See "Connecting to External Equipment" (P.5).
pressure
Fix the power supply wiring and other communication

terminal
wirings with the clamper (supplied) securely.
(Do not apply tensile force on the terminal connection part.)
Connect the LAN cable.

After all wiring arrangements are complete, turn

the circuit breaker on.
• Before power on, measure the voltage of the power supply
terminal board, and check it for the specifi ed voltage.
Turning the power on with a voltage other than the
specifi ed one may blow the fuse. If this occurs, no power
Screw
is supplied, and this unit may need to be replaced.
4
.
2
(When connecting to a network)
Ground
shield wiring
)
*4