Campbell Hausfeld TL054589 Instrucciones De Funcionamiento

See Warranty on page 4 for important information about commercial use of this product.
Operating instructions
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or
property damage! Retain instructions for future reference.
RegisteR youR pRoduct online now!
Description
Professional drills are air tools designed
for drilling, honing, reaming, hole
sawing and wire brushing.
The 1/2" models offer high torque and
low RPM providing extra power for
large drill bits. Great for drilling studs
for electrical wiring.
The 3/8" models operate at high speed
making the tool ideal for drilling metal
and pilot holes which reduce wood
splitting when installing screws. The
keyless chuck model provides fast and
convenient drill bit changes and some
feature a reverse mode to disengage
jammed bits.
Unpacking
When unpacking this product, carefully
inspect for any damage that may have
occurred during transit.
General Safety
CALifOrNiA PrOPOSiTiON 65
You can create dust when you
cut, sand, drill or grind
materials such as wood, paint,
metal, concrete, cement, or other
masonry. This dust often contains
chemicals known to cause cancer, birth
defects, or other reproductive harm.
Wear protective gear.
This product is a part of a high pressure
system and the following safety
precautions must be followed at all
times along with any other existing
safety rules.
1. Read all manuals included
with this product carefully.
Be thoroughly familiar
with the controls and the
proper use of the equipment.
2. Only persons well acquainted with
these rules of safe operation should
be allowed to use the air tool.
REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping.
© 2012 Campbell Hausfeld/Scott Fetzer
ing pressure of the air tool (90 psi). This
can reduce the life of the tool.
3. Do not exceed any pressure rating
of any component in the system.
4. Disconnect air tool from air supply
before changing tools or attach-
ments, servicing and during non-
operation.
and ear protection must be
worn during operation.
5. Do not wear loose fitting clothing,
scarves, neck ties or jewelry when
operating any tool. Loose clothing
or jewelry may become caught in
moving parts and result in serious
personal injury.
6. Do not depress trigger when
connecting the air supply hose.
7. Always use attachments designed
for use with air powered tools. Do
not use damaged or worn
attachments.
8. Never trigger tool when not applied
to a work object. Attachments must
be securely attached. Loose
attachments can cause serious
injury.
9. Protect air lines from damage or
puncture.
10. Never point an air tool at oneself or
any other person. Serious injury
could occur.
11. Check air hoses for weak or worn
condition before each use. Make
sure all connections are secure.
MANUAL
Release all pressure from the
system before attempting to
install, service, relocate or
perform any maintenance.
For parts, product & service information
visit www.chpower.com
Air Drills
http://www.chpower.net/reg
Do not exceed the 12. Keep all nuts, bolts and screws tight
maximum operat-
and ensure equipment is in safe
working condition.
13. Do not put hands near or under
moving parts.
14. Always secure work with clamps or
in a vise.
working in awkward positions and
repetitive work motions can cause
Safety
injury to hands and arms. Stop using
glasses
any tool if discomfort, numbness,
tingling or pain occur and consult a
physician.
Assembly
SySTem SeTUP
PLEASE REFER TO AIR TOOL AND SPRAY
GUN SET-UP (IN170102AV) FOR AIR
SYSTEM HOOK-UP INSTRUCTIONS.
Using fittings or air hoses which are too
small can create a pressure drop which
will result in a loss of power in the tool.
NOTe: Do not install a quick coupler set
between the tool and whip hose.
Air TOOL SeTUP
Ensure tool is not connected to air
supply then place tool upside down on
workbench.
Use of 3/8" fittings with 1/4" NPT
threads is recommended. Most
compressors are shipped with a short,
1/4" I.D. hose. For proper performance
and more convenience, use a 3/8" I.D.
hose. Hoses longer than 50 feet should
be 1/2" I.D.
the hose to move the tool or a
compressor. Keep hoses away from
heat, oil and sharp edges. Replace any
hose that is damaged, weak or worn.
TL054589
Excessive exposure
to vibration,
Never carry a tool
by the hose or pull
IN738300AV 1/12