Factory Settings - Siemens SIRIUS 8WD4428-0BC Guia De Inicio Rapido

EASY configuration (refer to figure IV)
Activate the GSM radio element:
- At least one element of the signal column must be lit.
Attention: As soon as voltage is applied to the module, it is ready to receive for 10 minutes. After this time it switches off
again.
- During this time the status LED on the top must change from a constant light that is on for approximately 5 s to flashing
(200 ms interval) with a 1 s break.
- Dial the number of the GSM radio element on your master phone. Wait until you hear the acknowledgement signal. Then end
the call.
- You will receive a configuration text message as confirmation.
- The GSM radio element is ready for operation. A text message is send to the master phone as long as a signal is applied to
the column for at least 30 s (if operating light is on) or 60 s (if it is off).
For individual adjustments refer to the "EXPERT" configuration section.
"EXPERT" configuration
The "EXPERT" configuration allows you to configure the GSM radio element individually via text message.
Procedure
- Send a text message (refer to the example for structure and content) to the phone number of the GSM radio element.
- The text message can only be sent from the master phone.
- Voltage must be applied to the GSM radio element.
Syntax of the configuration text message
- Each configuration text message must start with "conf,gsm1 "
- Do not use semicolons.
- Blanks, full stops and commas are allowed.
- There is no distinction between upper and lower case letters.
- The parameters are separated by a blank ( ).
- The alarm texts must end with a semicolon! Alarm texts can consist of up to 120 characters of ASCII text max. (refer to
example).
- If you need a confirmation from the GSM radio element add a "+" without a blank at the end of the text message.
- Only the master phone will get a confirmation text message.
Configurable Default setting
parameters
c1: last 6 character-
sof the IMEI No.
Device ID (name)
c2:
–
Phone number of master
phone
c3: –
Phone number of operator
2
c4: –
Phone number of operator
3
c5:
1111
Master input mask
c6: 0000
Input mask of operator 2
(optional)
c7: 0000
Input mask of operator 3
(optional)
c8:
10
Duration of the alarm call
c9: 0
Operating mode
c10: 0001
External control mask
c11: signal 1
Alarm text 1
c12: signal 2
Alarm text 2
c13:
signal 3
Alarm text 3
c14: signal 4
Alarm text 4
1111: 1. digit = 1. level, 2. digit = 2. level, 3.digit = 3. level, 4.digit = 4.level. A voice call is free of charge.
Examples:
1. Changing the device ID to "machine1" with confirming text message:
conf,gsm1 c1:machine1 +"+" = confirmation
2. Additional message to a second phone (e.g. land line), voice call and text message if signal at the first level of the signal
column. Confirmation via text message:
conf,gsm1 c3:+4974249557222 c6:3000 +
3. Specify alarm text:
conf,gsm1 c11: machine 1 failure; conf,gsm1 c12: alarm channel A
4
Description
Max. 12 characters, any ASCII text (optional), can be allocated to the GSM
radio element during configuration.
Phone number with max. 20 digits, international format (with "+")
Phone number with max. 20 digits, international format (with "+")
(optional)
Phone number with max. 20 digits, international format (with "+")
(optional)
Which input causes which sort of message, 4 characters:
4
0 – input is ignored
3
1 – input cause a text message
2
2 – input causes a voice call
1
3 – input causes a voice call and a text message
GSM
in seconds, possible values 2 to 60
Information on different operating modes
0 – default setting 1 – "external control" mode
One of the four levels is used as "alarm deactivated" input.
The selected level is defined in the mask.
ASCII text, max. 120 characters
(end with ";"!)
ASCII text, max. 120 characters
(end with ";"!)
ASCII text, max. 120 characters
(end with ";"!)
ASCII text, max. 120 characters
(end with ";"!)

Factory settings

Factory setting mode:
A GSM radio element without master phone number is in
factory setting mode. The GSM radio element can be confi-
gured.
Reset to factory settings
Send a text message to the GSM radio element with the
IMEI number. (15 characters) followed by the word "reset"
with a blank!
Example: 351266000233017 reset
You will not get a confirming text message. The GSM radio
element is in factory setting mode when it switches off auto-
matically after 10 minutes.
Status check
The status of the GSM radio element can be checked using
the master phone. Send a text message: "ST+". You ill
receive a text message containing the status of the GSM
radio elements.
Example: Send text message: ST+
Index Name
1 Device ID
2 Status of the 4 inputs
3* System run time in seconds
4* Number of text messages sent 1 to 8 digit number
5* IMEI
6 Activate / deactivate alarm
You can obtain information marked with a "*" by sending a
message with "STX+". The seconds are counted from the
moment the GSM radio element is switched on. "4*" started
counting the moment the device was switched on or when
the counter was last reset.
Resetting te text message
A text message with "STX RSMS" deletes the current
counter reading (check with pre-paid cards). You will receive
a confirmation text message if you add a "+".
Example: STX RSMS
Current configuration
Send a configuration text message to the GSM radio ele-
ment. The text message has no configurable content. The
current counter reading (check with pre-paid cards). You will
receive a confirmation text message if you add a "+".
Example: conf,gsm1 +
Troubleshooting
If faults are detected during the initializing phase, these
faults are signaled via flashing sequences of the status LED
(refer to illustration under "EASY" configuration):
- LED flashes 2 x (200 ms interval), 1s break:
-> no SIM card detected
- LED flashes 3 x (200 ms interval), 1s break:
-> PIN number not set to 0000
- LED flashes 4 x (200 ms interval), 1s break:
-> Hardware fault. Switch off the GSM radio element and
clear the fault. No regular operation is possible in these
states.
The GSM radio element is OK. However, you do not receive
any message on your cell phone:
- Deactivate the identification restriction on the master
phone!
8ZX1012-0WD44-0CA1
Description
4 digit number
1 to 8 digit number
15 digit number
"ON" / "OFF"