Tabla de contenido
Publicidad
DRS-982 + PDH-227 = DRS-982K
1
Available BULIK Chime Versions
PDH-227
DRS-982
2
Remove the chime from the socket outlet
Power supply indicator -
LED, yelolow
Ringing indicator - LED, red
speaker
4
The chime code setting
5
The push-button code setting
7
Remove the transparent cover
a
b
Bell push PDH-227
Remove the cover
c
Bell push components
cover
card
button
DRS-982K_inter.indd 4-5
PDH-991
PDB-233
RT-236
3
Remove the chime cover
NOTE!
Remove the bell from the
socket outlet before you
remove the cover.
NOTE!
Remove the bell from the
socket outlet before you
remove the cover.
Sound volume
adjustment
Here lever the cover
6
The sound type selection inside the push-button
DING, DING
DING-DONG,
DING-DONG
8
Loosen the mounting screw
Diode
GB
WIRELESS CHIME BULIK WITH HERMETIC PUSH-BUTTON DRS-982K
•
Perfect as a doorchime, a restaurant / hotel "reception" chime, an internal recall device
•
The doorchime installation is not needed
•
Chime connected directly to 230 V AC socket outlet
•
The push-button battery operated
•
The push-button is adapted to changeable weather conditions
•
Useful at home, a restaurant, a hotel, a company office, and for special care people
•
Radio transmission (433.92 MHz operating frequency)
•
Range of work: 100 m* in open area
•
Possibility of setting the user's individual code (16 codes to select)
•
Possibility of interoperation with the following wireless push-buttons simultaneously: PDH-991 (hermetic, 150 m* operating range), PDH-227
(hermetic, 100 m* operating range) and PDB-233 (the reception chime, 100 m* operating range)
•
It is possible to increase the number of the chimes and push-buttons, if needed
•
Possibility of increasing the operating range by means of RT-236 retransmitter of ZAMEL (by another 100 m*)
•
Two sounds to select (a possibility of identification of the push-button pushed)
•
Loudness volume control
•
Optical signalling (LED) of the chime and the push-button operation
•
Chime sound: DING - DING or DING - DONG, DING - DONG
•
Sound level: approx. 85 dB
I. TECHNICAL DATA
WIRELESS CHIME BULIK DRS-982
Sound level: approx. 85 dB
Coding: 16 channels
Power supply: 230 V AC / 50 Hz
Stand-by power consumption: 1,8 VA
Maximum power consumption: 2,8 VA
Transmission: radio
Operating frequency: 433.92 MHz
Protection class: II
IP protection: IP 20
Chime sound: DING-DING or DING-DONG, DING-DONG
Temperature operating range: 0°C ÷ 35°C
PDH-227 PUSH-BUTTON, WIRELESS, HERMETIC
Power supply: MN21 / 23A 12 V battery
Transmission: radio
Operating frequency: 433.92 MHz
Transmitter power output: < 5 mW
Operating range: 100 m* in open area
Coding: 16 channels
Transmission signalling: optical (LED, red)
IP protection: IP 44
Temperature operating range: -20°C ÷ 35°C
*The given range concerns opened area i e perfect conditions, without obstacles. If between the transmitter and the receiver obstacles are found, then it
can be expected smaller range for: wood and plaster from 5 to 20%, the brick from 20 to 40%, armed concrete from 40 up to 80%. By metallic obstacles
applying radio systems isn't being recommended from the attention for considerable limiting the radius. Also overhead and underground power lines have
the negative influence on the range of big power and transmitters of the GSM network put in the walking distance of devices.
II. INSTRUCTION MANUAL
a) How to launch the chime
1. Check if there is a complete set in the package (the chime, PDH-227 chime push-button with a battery, 2 plastic wall plugs + 2 screws, 1
section of the double-sided adhesive tape, impaired seal with an overprint on the chime back wall).
2. Check if voltage in your socket outlet is 230 V AC.
3. Insert the chime into 230 V AC socket outlet (Fig. 2).
4. Check if the yellow LED in the chime casing lights.
5. At the selected point place the chime push-button onto the substrate and check its operation by means of pushing the push-button.
6. If the chime operates correctly, fix the push-button at the previously selected place with the use of the wall plugs or the double-sided adhesive
tape.
b) The sound level adjustment
1. Remove, levering it with the use of a screwdriver, the longitudinal cover placed on the chime front side horizontally. There are the code
switches and the sound level adjustment handwheel under the cover (Fig. 3, 4).
2. Adjust the sound level to your needs with the handwheel.
3. Place the chime switches cover.
c) Code changing
1. All the chimes have the same factory set code. In order to avoid automatic chime start (e.g. by your neighbour) it is recommended to set the
user's individual code.
2. Remove the chime from the socket outlet (Fig. 2).
3. With the use of a screwdriver, remove the transparent stopper and the plate from the push-button front side (Fig. 7).
4. Unscrew the screw placed in the middle of the casing and remove the casing upper part (Fig. 8).
5. Remove, levering it with the use of a screwdriver, the longitudinal cover placed on the chime front side horizontally. There are the code
switches and the sound level adjustment handwheel under the cover (Fig. 3).
6. With the use of switches 1, 2, 3, 4 inside the chime and the push-button set the same code selected by yourself (Fig. 4, 5).
7. Place the chime switches and the push-button cover.
8. Insert the chime into socket outlet
9. Check the chime operation by means of pushing the push-button.
10. Place the push-button casing, screw the fixing screw and place the stopper and the plate.
d) Sound type selection
1. With the use of a screwdriver, remove the transparent stopper and the plate from the push-button front side (Fig. 7).
2. Unscrew the screw placed in the middle of the casing and remove the casing upper part (Fig. 8).
3. With the use of switches 5 and 6 inside the push-button set the selected sound type. Please, remember to set the switches in different
positions. If not, the chime will not operate (Fig. 6). If you have two push-buttons, set two different sound types in order to recognise which
one has been pushed.
4. Check the chime operation by means of pushing the push-button.
5. Place the push-button casing, screw the fixing screw and place the stopper and the plate.
NOTE!
1. The wireless chime is ready to use after approx. 10 seconds after inserting into the socket outlet.
2. The wireless chime is being operated with the use of radio waves. Therefore, if there are obstacles on the signal way (walls, metal / concrete
structures), the device operating range may decrease significantly.
3. It is recommended to avoid mounting the push-button directly on a metal substrate.
4. If the chime operating range is insufficient, you may increase the range by 100 m* with the use of RT-236 retransmitter of ZAMEL.It is
recommended to use the retransmitter in high volume rooms and complex shape objects. If needed, it is possible to increase the number of
retransmitters in order to cover the whole object area of any dimensions.
5. If any automatic chime starts occur, it means that there is another chime system in the neighbourhood running in the same channel.It is
necessary to change the device code.
6. All the chimes have the same factory set code.
The Declaration of Conformity is on our Website www.zamel.com
ZAMEL devices marked
with this sign can work
with each other
06.11.2015 11:41
Publicidad
Tabla de contenido
