Assembly; Assembly For Lsv 6; Installing Wheels (03); Installing Operating Arms (04) - AL-KO LSV 6 Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 120

Assembly

If the case with the log splitter is not already in an
upright position:
1. Lift case (02/1) on one side (02/a) with two
persons. Take care that the case does not
slip. If necessary: Push a block (02/2) under
the opposite side to support the case.
2. Raise the case until it is upright and straight.
3. Cut open the case carefully on the underside
using a knife (02/3), taking care that the ap-
pliance is not damaged.
4. Lift the case off the appliance (02/b).
5. Check the scope of supply (see chapter 2.3
"Scope of supply", page 31).
5 ASSEMBLY
WARNING!
Danger if assembly is
not carried out complete-
ly!
Operation of an incom-
pletely assembled appli-
ance can result in serious
injury.
Only operate the appli-
ance when it is fully as-
sembled.
Check that all safety
and protective devices
are in place and func-
tioning correctly before
switching on.
5.1
Assembly for LSV 6
5.1.1

Installing wheels (03)

Perform the steps described here for both
wheels:
1. Push wheel axle (03/1) into holder (03/2) on
the base unit from below (03/a) and hold
tight.
2. To secure the wheel axle, screw two M6 x 8
screws (03/3) securely into the bores above
one another in wheel axle and holder.
442310_a
3. Push wheel (03/4) and washer (03/5) onto
the wheel axle (03/b).
4. Push cotter pin (03/6) through the bore in the
wheel axle to prevent the wheel from falling
off (03/c).
5. Push on (03/d) wheel cap (03/7).
5.1.2

Installing operating arms (04)

Perform the steps described here for both operat-
ing arms:
1. Place operating arm (04/1) on transverse
plate (04/2) so that their mounting bores are
aligned. Insert the lever of pump controller
(04/3) into the recess in the operating arm.
Note: Pay particular attention that the lever
of the pump controller is inserted correctly!
2. Insert M10 x 30 screw (04/4) with washer
(04/5) through the bores in operating arm and
transverse plate.
3. Push second washer (04/6) and self-locking
nut (04/7) from below onto the screw and
tighten securely.
5.2
Assembly for LSV 7 and LSV 8
5.2.1

Installing wheels (05)

Perform the steps described here for both
wheels:
1. Push the following parts onto wheel axis
(05/1):
Wheel (05/2)
3 washers (05/3)
2. Push wheel axis with wheel and washers into
bearing (05/4) as far as it will go (05/a).
3. Push spring cotter pin (05/5) through the bore
in the wheel axle until it engages (05/b).
4. Push on (05/c) wheel cap (05/6).
5.2.2

Installing operating arms (06)

Perform the steps described here for both operat-
ing arms:
1. Pull spring cotter pin (06/1) out of locking pin
(06/2).
2. Pull locking pin out of transverse bracket
(06/3).
3. Coat operating arm (06/4) slightly with grease
at points (06/A) and (06/B).
4. Push operating arm (06/4) into transverse
bracket (06/3) and onto the level of pump
controller (06/5).
Note: Pay particular attention that the lever
of the pump controller is inserted correctly!
39

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Lsv 7Lsv 8113602113603113601

Tabla de contenido