Settings Through The Control Panel; Machine Preparation; Operating Information Battery Charging - Comet Spa CRS 75 BT Manual De Instrucciones

Insert the battery putting the opening in the box
(only for the Pb-Acid battery) in a position to run the
electric wiring to the connector of the machine wir-
ing.
After checking that all the controls on the panel are in
position "0" or at rest, connect the battery connector
to the machine connector.
Close the battery compartment (lowering the re-
covery tank) making sure not to crush any wires.
6.3 SETTINGS THROUGH THE
CONTROL PANEL
When switching on the machine using the key switch
(Photo M-1), press simultaneously the BRUSH key
(Photo M-5) + SUCTION key (Photo M-4) on the con-
trol panel (Photo M).
When the display (Photo M-9) shows "TARATURA???"
(CALIBRATION???), also press the SPEED REDUCTION
key (Photo M-3) without leaving the other keys.
When the message "TARATURA" (CALIBRATION) is
shown, release the keys previously pressed.
It is now possible to scroll through the settable pa-
rameters pressing the BRUSH key (Photo M-5) and
the SUCTION key (Photo M-4):
- TIPO LOGO (LOGO TYPE)
- TIPO BATTERIA (BATTERY TYPE)
- CONTRASTO (DISPLAY CONTRAST)
- LINGUA (LANGUAGE)
- RIT. TASTI (KEYS DELAY)
To select and change the desired parameter, press
the SPEED REDUCTION key (Photo M-3). With the
BRUSH key (Photo M-5) and the SUCTION key (Photo
M-4) it is possible to increase or decrease the set
value. To confirm the new value, press the SPEED
REDUCTION key (Photo M-3).
To exit the calibration select EXIT, and press the
SPEED REDUCTION key (Photo M-3).
MEANING OF SETTABLE PARAMETERS:
LOGO TYPE
Range: CTM, FASA, LAVOR
BATTERY TYPE
Range: Pb Acid / Gel
CONTRAST
Contrast value for the display.
LANGUAGE
Language that is displayed. In this version are avai-
lable: ITALIAN, FRENCH, ENGLISH, GERMAN, SPANISH.
KEYS DELAY
Delay in hundredths of second between the accep-
tance of consecutive pressures of the keys. Establi-
shed to limit communication problems.
6.4

MACHINE PREPARATION

Before starting to work, wear non-slip shoes,
gloves and any other personal protection device indi-
cated by the supplier of the detergent used or consid-
ered necessary based on the operating environment.
Do the following before starting to work. Refer to
the relative sections for a detailed description of these
steps:
Check the battery charge level and charge, if neces-
sary.
Mount the brushes or scraper disks (with the abrasive
disks) that are suitable for the surface and work in-
volved.
Mount the squeegee, check that it is solidly attached
and connected to the suction hose and that the dry-
ing straps are not too worn.
Make sure that the recovery tank is empty. If not,
empty it completely.
Check and completely close the detergent solution
release control.
Fill the detergent solution tank with a mix of clean
water and non-foaming detergent in an adequate
concentration through the rear hole. Leave 7 cm
between the mouth of the plug and the level of the
liquid.
To avoid risks, become familiar with the machine
movements, carrying out test runs on a large surface
without obstacles.
To obtain the best results in terms of cleaning and
equipment service life, you should do the following
simple but important operations:
- Identify the work area, moving all possible obstacles
out of the way; if the surface is very extensive, work in
contiguous and parallel rectangular areas.
- Choose a straight work trajectory and begin working
from the farthest area to avoid passing over areas that
have already been cleaned.
7. OPERATING INFORMATION
7.1 BATTERY CHARGING
Prepare and check the battery charge according to
the instructions provided in the specific section.
Detach the battery connector (the one with the han-
dle) from the machine power connector and connect
it to the battery charger connector.
Do not connect the battery charger to the scrub-
ber-drier's main wiring connector.
Hold the connectors with the hands; do not pull them
using the cables.
If the machine is equipped with Pb-Acid batteries,
charge only in a well-ventilated area, lift the top tank
and open the battery plugs.
Follow the steps indicated in the battery manufac-
36