Ryobi R18TL Traducción De Las Instrucciones Originales página 3

Safety, performance, and dependability have been given
top priority in the design of your tripod area light.
INTENDED USE
The tripod area light is intended for general illumination
of most work area spaces. Do not use the product in wet
conditions.
Do not use the product for any other purpose. Use of the
product for operations different from intended could result
in a hazardous situation.
TRIPOD AREA LIGHT SAFETY WARNINGS
The light source contained in this luminaire shall only be
replaced by the manufacturer or his service agent or a
similar qualified person.
Use only with recommended battery pack and charger.
Any attempt to use another battery pack will cause
damage to the product and could possibly explode,
cause a fire, or personal injury.
Do not disassemble the product.
The product is non-dimmable; do not connect with any
dimmers.
If wrapped or in contact with fabrics, the lens can
produce sufficient heat to melt some fabrics. To avoid
serious personal injury, never allow the lens to come in
contact with anything.
Do not direct the light beam at persons or animals and
do not stare into the light beam yourself (not even from
a distance). Staring into the light beam may result in
serious injury or vision loss.
Do not place the product or battery pack near fire or
heat. This will reduce the risk of explosion and possible
injury.
Do not place hands or fingers between adjustable head
and frame when positioning work light to avoid possible
pinching.
To reduce the risk of electric shock, do not expose to
water or rain. Do not place or store the product where it
can fall or be pulled into a tub or sink.
To reduce the risk of injury, close supervision is
necessary when the product is used near children.
To reduce the risk of injury or damage, avoid contact
with any hot surface.
Check to make sure the product does not rock, slide or
move prior to use.
Put the product on a firm level surface where there
is plenty of room to handle and properly support the
product.
Remove the battery pack before starting any work on
the product.
Do not store the product in a damp or wet location, or in
a location where the temperature may reach or exceed
40°C (104°F). For example, inside sheds, vehicles, or
metal buildings in the summer.
ADDITIONAL BATTERY SAFETY WARNINGS
WARNING
damage due to a short circuit, never immerse your
as seawater, certain industrial chemicals, and bleach
or bleach-containing products, etc., can cause a short
circuit.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps
or tape. Do not transport batteries that are cracked or
leaking. Check with the forwarding company for further
advice.
KNOW YOUR PRODUCT
See page 55.
1. Adjustable head
2. Upper tube
3. Middle tube
4. Lower tube
5. Lock clamp
6. Handle
7. Foot
8. Battery port
9. On/Off button
10. Release button
MAINTENANCE
Use only original accessories and spare parts. Should
components need to be replaced which have not been
described, please contact an authorised service centre.
All repairs should be performed by an authorised
service centre.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to various types of commercial
solvents and may be damaged by their use. Use clean
cloths to remove dirt, carbon dust, etc.
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or
destroy plastic which may result in serious personal
injury.
SYMBOLS ON THE PRODUCT
Safety alert
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL
English | 1