Redmond RK-M142-E Manual Del Usuario página 7

No serial number identification sticker on the appliance automatically disables
the user's right to aftersale service .
Wipe the base of the appliance with a damp cloth, then let dry. You may notice
foreign smell when first using the appliance, this does not mean its malfunction.
After the appliance transportation or storage at low temperature keep it at
room temperature for at least two hours before plugging in.
You are advised to boil water in the kettle a few times before use to get foreign
smell out and disinfect the appliance.
II. OPERATION
Preparation
1. Fix the kettle with the base to the solid even dry horizontal surface. Make
sure the outgoing vapour during boiling does not fall on wallpaper,
decorative coats, electric units and other items, which can be damaged
by humidity and high temperature.
2. Unwind the power cord to the desired length. Put the excessive part into
the recess at the bottom of the stand. Use the extender of appropriate
capacity if necessary (no less than 2.5 kW).
3. Lift the kettle off the base. Press the opening button on the appliance
lever.
4. Pour water into the kettle. Water level should be between minimum and
maximum levels on the inner surface of the appliance frame. If the kettle
is overfilled it could cause boil-over. The unit will turn off prematurely
in case of water shortage.
ATTENTION! The unit is meant only for water heating and boiling.
5. Firmly close the kettle lid and fix it to the base. The unit will work only
if it is fixed correctly.
6. Plug in the kettle.
Water boiling
1. Press the «0/I» button. A short audible signal will be heard, and the process
of water heating will start. Button illumination will light up solid during
the operation.
2. The appliance will be automatically turned off after boiling.
3. To interrupt the heating process lift the «0/I» button.
The settings are saved if the kettle is lifted off the base during operation. The appli-
ance operation will be restarted automatically after returning the kettle to the base.
Safety system
• The kettle is supplied with an automatic shut-off system upon boiling.
• In case of water shortage the automatic overheat protection will turn off
the kettle. Wait till the appliance is cooled, thereafter it will be ready for
operation.
III. CLEANING AND MAINTENANCE
Unplug the kettle and allow it to cool before cleaning.
DO NOT USE solvents (petrol, acetone, etc.), abrasive cleansers, and abrasive
coated sponges while cleaning.
ATTENTION! Before repeated usage make sure that the electrical contacts are kept dry!
Base and body cleaning
Clean the kettle body and base with a soft cloth. Dry the kettle before operation.
ATTENTION! Never immerse the kettle, the base, the power cord or the socket
in water: the electrical contacts should not contact with water.
Descaling
During operation, depending on the composition of usable water, oxide spots
and scale can appear on the heating element and inner walls of the appliance.
To remove it use special nonabrasive cleansers for scale cleaning and removal
from kitchen appliances.
1. Pour water into the kettle ¾ from maximum capacity and bring to a boil.
2. After the kettle turns off, add eight percent acetic acid solution to the
maximum level on the inner surface of the body.
3. Leave this solution inside the kettle for several hours.
4. Empty the kettle and rinse properly.
5. Fill the kettle with clean water up to the maximum level on the inner
surface of the body and bring it to boil.
6. Empty the kettle and rinse it again. If scale still remains, repeat the
procedure mentioned above.
You can also use special means for descaling. Follow manufacturer's instructions
in this case.
Removable scale filter cleansing
1. Open the lid. Remove the filter pulling it upward.
2. Rinse the filter. You can use a dishwashing solution.
3. Place the filter into the kettle with the projection to the centre.
RK-M142-E
GBR
7