Black and Decker KS710LK Manual De Instrucciones página 6

ENGLISH
Hold the saw blade (13) as shown, with the teeth facing
forward.
Insert the shank of the saw blade into the blade holder (14)
as far as it will go.
Tighten the screw (12).
Fitting and removing the parallel fence (fig. B)
the parallel fence is used to saw in a straight line parellel to
the edge of the workpiece. The fence can be fitted both to the
left side and to the right side.
Fitting
Loosen the locking knob (15).
Insert the parallel fence (16) through the openings (17).
Slide the parallel fence into the desired position.
Tighten the locking knob.
Removing
Loosen the locking knob (15).
Pull the parallel fence off the tool.
Connecting a vacuum cleaner to the tool (fig. C)
Slide the dust extraction adaptor (10) into the shoe plate (8)
until it locks in position.
Connect the vacuum cleaner hose (18) to the adaptor (10).
Make sure that the dust shroud (6) is fitted.
Use
Warning! Let the tool work at its own pace. Do not overload.
Adjusting the shoe plate for bevel cuts (fig. D)
The shoe plate can be set to a left or right bevel angle of up to
45°.
Remove the dust extraction adaptor (10) if fitted.
Loosen the screw (19).
Pull the shoe plate (8) forward, set it to the required angle
and push it back into place. You can use the scale or a
protractor to check the angle.
Tighten the screw (19).
To reset the shoe plate for straight cuts:
Loosen the screw (19).
Pull the shoe plate forward and set it to an angle of
approx. 0°.
Push the shoe plate backward and tighten the screw (19).
Use a square to check the angle.
Setting the pendulum stroke
Set the pendulum stroke selector (9) to the desired position.
Position 0: for laminates and sheet metal
Position 1-2: for plywood, metal and aluminium
Position 2-3: for soft wood and pvc
6
Variable speed control
Set the variable speed control knob (3) to the required
speed range. Use a high speed for wood, medium speed
for aluminium and PVC and low speed for metals other
than aluminium.
Switching on and off
To switch the tool on, press the on/off switch (1).
For continuous operation, press the lock-on button (2) and
release the on/off switch.
To switch the tool off, release the on/off switch. To switch
the tool off when in continuous operation, press the on/
off switch once more and release it.
Hints for optimum use
Sawing laminates
As the saw blade cuts on the upward stroke, splintering may
occur on the surface closest to the shoe plate.
Use a fine-tooth saw blade.
Saw from the back surface of the workpiece.
To minimise splintering, clamp a piece of scrap wood or
hardboard to both sides of the workpiece and saw through
this sandwich.
Sawing metal
Be aware that sawing metal takes much more time than
sawing wood.
Use a saw blade suitable for sawing metal.
When cutting thin sheet metal, clamp a piece of scrap
wood to the back surface of the workpiece and cut
through this sandwich.
Spread a film of oil along the intended line of cut.
How to use the laser (fig. E)
the laser projects the line of cut on the workpiece surface.
To switch the laser on, press the button (4).
To switch the laser off, press the button (4) again.
viewing from directly above the saw, the line of cut can be
easily followed. Should this view be restricted for any reason,
the laser can be used as an alternate cutting guide.
Use a pencil to mark the cutting line.
Position the saw over the line.
Switch on the laser.
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance, switch off and
unplug the tool.