Manual Code Search; Automatic Code Search - Emtec Universal EKCOH420 Manual Del Usuario

4) Programming your TV and AUX modes
Note: You can dedicate any appliance (TV, DVD, SAT...) to the AUX key: you just need to enter the 4 digit code
(found in the code book) of the appliance, i.e. a DVD code under the AUX key. In any case, follow the steps below:
1. Make sure your equipment is switched on (for example TV).
2. Press and hold the S (2) key until the LED indicator (1) lights continuously. Release the S key.
3. Press and release the mode key (9) of the device you want to control (for example TV).
4. Enter the 4 digit code (12) from the Code Book. The LED (1) turns off after the last digit is entered. If you
entered a wrong code the LED blinks for 3 seconds and then goes off. You have to repeat from step .
5. Point the remote in the direction of your TV and press the POWER button (3). Your device should turn
off. Check other functions (for example for a VCR: FF or REW etc.). If certain functions are not responding
this indicates that the entered code is not the correct one. In that case repeat the above procedure with the next
corresponding code of your brand.
6. Repeat this procedure from step 1 for the other equipment you want to control (TV, VCR, DVD, SAT)

5) Manual code search

If your equipment (TV, SAT etc....) does not respond, try the other codes for your brand. If it still doesn't
respond, try the Code Search method.
Note: As you can dedicate any appliance (TV, DVD, SAT...) to the AUX keys you need first to enter any 4 digit
code for the kind of appliance you wish to control (found in the code book), i.e.: If you want to program a SAT
under the AUX key, enter any SAT code found in the code book and then follow the steps below:
, Make sure your equipment is switched on. If not switch it on manually.
2. Press and hold S (2) until the LED indicator lights (1) steadily. Release S key.
3. Press the mode key (9) that matches the equipment you want to control (for example TV).
4. Press PROG + (6) repeatedly until the PROG changes. If you step past the correct code use PROG - (6) to go
back to the right code.
5. When the equipment you want to control reacts press -/-- (13) to confirm the code. That's all.
Note: If your equipment doesn't have PROG +, you can use PLAY (VCR or DVD) (5) or POWER (3) key.
The search starts after the last registered code. If that was 0030, the search starts at 003 until the last possible
code and then goes from 0000 to 009.
Note: if certain functions of your equipment can't be controlled you have to find a different code for your brand.

6) Automatic code search

When searching an unknown code, you can step through the library automatically (AutoSearch). When your
equipment responds, you can stop the searching process and store the code you found.
Note: As you can dedicate any appliance (TV, DVD, SAT...) to the AUX key, you need first to enter any 4 digit
code for the kind of appliance you wish to control (found in the code book, i.e.: If you want to program a SAT
under the AUX key, enter any SAT code found in the code book and then follow the steps below:
. Turn on the device you want to control.
2. Press and hold S (2) until the LED indicator (1) lights steadily. Release S button.
3. Press the mode button (3) that matches the equipment you wish to control. The LED (1) blinks once.
4. Press PROG+ (6) once. After a few seconds the remote starts stepping through the code library (fast search,
1 code per second). When the device responds, you can press PROG+ (6) to switch to slow search (1 code per 3
seconds). You can step back by pressing PROG- (6) (you can step forward by pressing PROG+ (6) in case you
went too far back). As soon as the device responds again, press the -/-- key (13) to store the code you found.
7) Identifying codes found using the search procedure
1. Press and hold S (2) until the LED indicator (1) lights steadily. Release S key.
4