LiftMaster T Manual Del Usuario página 7

Ocultar thumbs Ver también para T:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

THREE BUTTON REMOTE CONTROL PROGRAMMED FOR OPEN/
CLOSE/STOP
NOTE: The following programming requires a LiftMaster
Monitored Entrapment Protection (LMEP) device.
®
Your Security+ 2.0
or dip switch remote control can be
programmed to operate as a 3-button wireless control station:
the large button will open the door, the middle button will close
the door, and the third button will stop the door's movement.
You may set up this feature as follows:
1. To enter programming press and release the RADIO button on
the logic control board (the RADIO LED will light).
2. To program the OPEN button to a remote control press and
release the OPEN button on the logic control board. The RADIO
LED will flash and then stay on solid. Then press the
corresponding button on the remote control. The RADIO LED
on the logic control board will flash, this confirms that the
remote control has been programmed. (By programming the
remote you use 1 channel of the 90 channels on the radio
receiver.)
3. To program the CLOSE button to a remote control press and
release the CLOSE button on the logic control board. The
RADIO LED will flash and then stay on solid. Then press the
corresponding button on the remote control. The RADIO LED
on the logic control board will flash, this confirms that the
remote control has been programmed. (By programming the
remote you use 1 channel of the 90 channels on the radio
receiver.)
4. To program the STOP button to a remote control press and
release the STOP button on the logic control board. The RADIO
LED will flash and then stay on solid. Then press the
corresponding button on the remote control. The RADIO LED
on the logic control board will flash, this confirms that the
remote control has been programmed. (By programming the
remote you use 1 channel of the 90 channels on the radio
receiver.)
5. After learning remote controls press the RADIO button on the
logic control board (RADIO LED will turn off). NOTE: If no
activity within 30 seconds, the MAS and RADIO LED's will flash
briefly to indicate the RADIO has exited the programming mode
for remote controls and keyless entry devices. The RADIO will
remain in program mode for another 150 seconds for MyQ
devices and then will completely exit with no activity.
Open
Close
Stop
REMOTE CONTROL PROGRAMMING FEATURE
Program Remote Controls from the 3-button control station
(3BCS).
This feature allows the user to add additional remote controls
from the 3BCS. By default the remote control learn option is off.
NOTE: Requires access to the operator electrical box to enable or
disable this feature.
To turn this feature on:
1. Turn the SELECTOR DIAL to PROG.
2. Press and release the RADIO button. The RADIO LED will be lit.
3. Press and release the MID button. The RADIO LED will flash
quickly 6 times.
4. Press and release the RADIO button. The RADIO LED will turn
off.
5. Return the Selector DIAL to the desired wiring type.
To add remote controls from the 3BCS:
1. With the door in the fully closed position (close limit activated),
press and hold STOP.
2. While holding STOP, press and hold CLOSE.
3. While holding STOP and CLOSE, press and hold OPEN.
4. Release all three buttons once the MAS LED has lit.
5. Learn a remote control by one of the following methods:
a. Programming a standard single button/single function
remote control, push and hold the remote control button
until the MAS LED goes out. Repeat steps 1 through 4 to
add additional remote controls.
b. Programming a 3-button/three function remote control
(open/close/stop), first push the button on the 3BCS
(Example: OPEN) and then press and hold the button on the
remote control (Example: large button) that you want to
correspond with the selected (Example: OPEN) command
until the MAS LED flashes and goes out. Repeat steps 1
through 4 to add additional buttons (close and stop).
To turn this feature off:
1. Turn the Selector DIAL to PROG.
2. Press and release the RADIO button. The RADIO LED will be lit.
3. Press and release the MRT button. The RADIO LED will flash
®
quickly 3 times.
4. Press and release RADIO button. The RADIO LED will turn off.
5. Return SELECTOR DIAL to desired wiring type.
NOTE: Restoring the operator to Factory Default (see RESETTING
FACTORY DEFAULTS) will also disable this feature. The remote
controls will still be learned.
7

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

SdGsdGtGh

Tabla de contenido