LiftMaster T Manual Del Usuario página 8

MYQ ® SETUP (OPTIONAL)
For Smartphone App, tablet or PC control, LiftMaster MyQ Internet
Gateway (model 828LM) is required.
1. To enter programming mode, press and release the RADIO
button on the logic control board (the RADIO LED will light).
2. To program the MyQ device, place the MyQ device into learn
mode (see instructions for the specific MyQ device).
3. When the programming is complete the RADIO LED will turn
off.
NOTE: If the programming is not completed within 3 minutes, the
program mode will be exited and the RADIO LED will turn off.
MAINTENANCE ALERT SYSTEM (MAS)
The Maintenance Alert System (MAS)
assists the installing dealer in setting up a
routine maintenance program. Once
programmed, the MAS notifies the end
user (with a flashing LED on the 3-button
station) when a preset number of cycles/
months has elapsed and scheduled
maintenance is due.
To Program:
1. Close the door.
2. Turn the selector dial to PROG.
3. Press and release the MAS SET button.
4. Press the STOP button once to clear the MAS memory.
5. Press the OPEN button once for every 5,000 cycles increments.
Press the CLOSE button once for every 3 month increments.
6. Press and release the MAS button to complete the
programming. The on board LED will flash back the
programmed settings. The OPEN LED will flash once for every
5,000 cycles. The CLOSE LED will flash once for every 3
months.
7. Turn the selector dial back to the desired wiring type.
NOTE: If MAS LED flashes 2 or more flashes in a row followed by
a pause, an operator error occurred. Turn to page 10 to diagnose
problem.
Example: A door is installed with 30,000 cycle springs and has an
annual service contract. To set the MAS, turn selector dial to
PROGRAM, press MAS button, press the STOP button to clear the
memory and then press the OPEN button 6 times (30,000 cycles)
and close 4 times (12 months). Press the MAS again to complete
the programming. Turn the selector dial back to desired wiring
type.
Special Notes about MAS: A 5th wire must be run to the control
station to activate the MAS LED. The MAS LED on the logic
control board is always enabled. When the operator is serviced
after the MAS LED has started to flash, repeat the setup procedure
to program in the number or cycles desired until the next service
visit OR press and hold the MAS button for 5 seconds in the
PROGRAM mode to reset the MAS with its current programmed
value. To disable the MAS, follow the programming procedure
above and press the STOP button to reset the counter to zero.
To Erase All MyQ
1. Press and release the RADIO button on the logic control board
2. Press and hold the MAS button for 5 seconds. The RADIO LED
All MyQ devices are now erased.
Please visit LiftMaster.com/MyQ-CD for troubleshooting
information.
Every time the operator leaves the close limit is counted as one
cycle.
Maintenance Alert LED
To view how many cycles are programmed into the MAS, set the
selector dial to DIAG and press the MAS button. The OPEN button
LED will flash once for every 5,000 cycle increment programmed
and the CLOSE button LED will flash once for every 3 month
increment programmed.
To view how many cycles have elapsed since the last time the
MAS was programmed, set the selector dial to DIAG and press the
MAS button. Press the OPEN button; the OPEN LED will flash
3-BUTTON CONTROL STATION once for every 5,000 cycles that has elapsed. Press the CLOSE
button; the CLOSE LED will flash once for every (3) months that
has elapsed. Press the MAS button to exit. Turn the selector dial
back to desired wiring type.
Press This
OPEN
CLOSE
8
® Devices:
(the RADIO LED will light).
will flash for approximately 5 seconds and the RADIO LED will
turn off.
To Get This
Adds 5,000 cycles to Maintenance Alert
System Activation Counter.
Adds 3 Months to Maintenance Alert System
Activation Timer.
STOP Clears memory, sets Maintenance Alert
System Activation Counter to 0 cycles and
0 months.
Set to PROG