SCHOLTES B 40 L EC Serie Manual De Instrucciones página 21

Important: Important: A pressure regulator, in compliance with Important: Important: Important:
the standards in force, must be inserted when
connecting to a liquid gas supply (in a cylinder).
Adapting to different types of gas Adapting to different types of gas Adapting to different types of gas
Adapting to different types of gas Adapting to different types of gas
To adapt the hob to a different type of gas other than
the default type (indicated by the label placed on the
upper part of the hob or on the packaging), the burner
nozzles should be replaced as follows:
• remove the hob grids and slide the burners off their
seats;
• unscrew the nozzles (fig. 7) using a 7 mm socket
spanner, and replace them with nozzles for the new
type of gas (see table 1 "Burner and nozzle
characteristics").
Fig. 7
After replacing the nozzles, change the hob After replacing the nozzles, change the hob After replacing the nozzles, change the hob
After replacing the nozzles, change the hob After replacing the nozzles, change the hob
setting using the control panel as follows: setting using the control panel as follows:
setting using the control panel as follows: setting using the control panel as follows: setting using the control panel as follows:
While the hob is switched off, press the power button
T1.
Press the lock button T2 (D1 lights up).
Press the buttons T2, T7 and T11 simultaneously,
holding them down until a numerical value appears on
the display D2.
At this point, with the hob set to methane G20 20 mbar,
the display shows 01; to convert the hob to operation
with G30 29 mbar, press the T4 button once, so that the
value 02 appears on the display D2. The hob will allow 2
adjustments to be made: 01 and 02, which correspond
to G20 20 mbar and G30 29 mbar respectively.
To save the new setting, press the buttons T2, T7 and
T11 simultaneously (hold them down for a few
seconds, until you exit the function – approximately 5
seconds); the hob will appear to be switched off with
the keypad locked. Press the unlock button T2 to
operate the hob.
NOTE: if, during the gas conversion procedure, no
buttons are pressed for a period of longer than 1
minute, the appliance automatically exits the function
without saving the new setting.
Once this procedure is complete, replace the old Once this procedure is complete, replace the old Once this procedure is complete, replace the old Once this procedure is complete, replace the old Once this procedure is complete, replace the old
rating sticker with one indicating the new type of rating sticker with one indicating the new type of rating sticker with one indicating the new type of
rating sticker with one indicating the new type of rating sticker with one indicating the new type of
gas used. Stickers are available in nozzle kits or gas used. Stickers are available in nozzle kits or
gas used. Stickers are available in nozzle kits or gas used. Stickers are available in nozzle kits or gas used. Stickers are available in nozzle kits or
can be obtained from any of our Technical can be obtained from any of our Technical
can be obtained from any of our Technical can be obtained from any of our Technical can be obtained from any of our Technical
Assistance Centres. Assistance Centres. Assistance Centres. Assistance Centres. Assistance Centres.
A
Setting the burners to minimum (only for gasG20) Setting the burners to minimum (only for gasG20) Setting the burners to minimum (only for gasG20)
Setting the burners to minimum (only for gasG20) Setting the burners to minimum (only for gasG20)
While the hob is switched off, press the power button
T1. Press the lock button T2 (D1 lights up).
Press the buttons T2, T5 and T9 simultaneously and
hold them down until the numerical value 01 appears
on the display 02; on the displays D3, 4, 5 and 6 a
numerical value appears which indicates the set
minimum level. This level ranges from 9. (the point
corresponds to a negative indication, i.e. -9) to 9:
there are therefore 19 minimum levels to choose
from. Press the + or – button corresponding to the
burner you are adjusting; the burner will be activated
at its maximum level to begin with, and will then be
adjusted to the minimum setting value indicated at
that moment by the display corresponding to that
burner. Use the + or – buttons corresponding to the
relevant burner to increase or decrease the minimum
level; if the minimum level is too low, causing the
burner to switch off or operate at such a low level
that the thermocouple does not detect the flame, the
burner operates at its maximum level for a few
seconds and then returns to the minimum level.
Repeat the process until the minimum level is high
enough. To save the minimum level setting for the
burner, as soon as it has been adjusted press the
corresponding + and – buttons simultaneously; if this
procedure is not performed the new setting will not be
saved. Once the adjustment procedures have been
completed for the various burners, press the T2, T5
and T9 buttons simultaneously (in this case the T2
button should be pressed slightly before the other
two); hold the buttons down for approximately 5
seconds, until the hob returns to the status of being
GB
21