Disposing Of The Battery - Telwin START PLUS 6824 Manual De Instrucciones

WARNING: DANGER!
Connect the mounting socket (Fig. A-1) to the starter's
12V or 24V power supply, checking the voltage
required for the vehicle to be started, and only after
being absolutely certain that the clamps have been
connected to the battery polarities correctly.
- Connect the mounting socket following the instructions
above.
- Turn the ignition switch or key of the vehicle or boat to
ON. Wait about one minute. Turn the vehicle ignition
switch or key to the start position for no more than 5÷6
seconds. If the vehicle or boat does not start, wait at
least 3 minutes before trying again.
Warning: Do not allow the black and red
clamps to come into contact with each other
or to touch a common conductor.
- Whilst the engine is running, disconnect the mounting
socket from the starter and the clamps from the vehicle
in the exact order seen below:
1. the mounting socket.
2. the black (negative) clamp.
3. the red (positive) clamp.
- Return the clamps to their housing on the starter.
It is highly recommended to recharge the starter as
soon as possible!
Using the starter as a 12V power supply unit by
means of the cigar-lighter type socket (Fig. A-4).
WARNING! 12V OUTPUT ONLY!
In case of overload the re-settable safety
switch will trip. To restore operation, remove
the cause of overload and press the button shown
in Fig.A-2.
- Take the cover off the cigar-lighter type socket (Fig.
A-4).
- Insert the cigar-lighter plug of the device to be powered
into the socket (Fig. A-4).
Recharging using a 230V AC power supply
Important! To protect the battery and lengthen
its working life, charge it for 12 hours before
using it for the first time, then after every time
it is used and, in any case, at least every 3 months.
It is possible to recharge the unit using the 230V AC
power adapter supplied. We recommend keeping the
battery fully charged at all times. A low charge level could
shorten the life of the battery. Bear in mind that the time
needed to recharge the battery depends on the number
of times it has been used. It is possible to check whether
the battery level is low by pressing the red button (Fig.
A-5).
The voltmeter (Fig. A-3) will indicate the battery charge
level. The green area of the voltmeter indicates that the
battery is charged.
Recharging
1- Connect the free starter plug at POSITION 12V,
making sure that the starter clamps are positioned in
the relative pocket and insulated from each other.
2- Insert the car cigarette lighter plug supplied with the
battery charger into the starter outlet (Fig. A-4).
3- Insert the battery charger plug into a 230 V socket.
4- Allow the starter to recharge for as long as necessary
(refer to the battery charger user manual).
5- When charging is finished remove the battery
charger and disconnect the free starter plug from
POSITION 12V.
Pb

DISPOSING OF THE BATTERY

When the starter battery is completely run down it should
be taken to a re-cycling depot. In some countries this is
mandatory. Contact the local special refuse authority for
information on recycling.
WARNING: Do not burn the battery to dispose of it.
This could cause an explosion. Before disposing of the
battery, apply insulating tape to the bare terminals to
prevent shorting. Do not expose the battery to intense
heat or fire as this could cause an explosion.
STARTER SPECIFICATIONS "4824"
Type of battery:
- rechargeable factory-sealed 12V acid-lead batteries.
Battery capacity:
- 40Ah.
Output current @ 24V:
- 2200A peak current;
- 800A starter current.
Output current @ 12V:
- 4400A peak current;
- 1600A starter current.
Copper cables:
- PVC insulated 16mm
Cable length:
- 190cm.
Output socket:
- 12V DC / max. current 10A.
General features:
- re-settable safety switch for output overload;
- automatic charging level reset switch;
- "cigar-lighter" type socket, 12V DC.
Weight:
- 24kg.
Standard accessories:
- T-CHARGE 12 Power supply / Battery charger (Fig. B).
STARTER SPECIFICATIONS "6824"
Type of battery:
- rechargeable factory-sealed 12V acid-lead batteries.
Battery capacity:
- 40Ah - 80Ah.
Output current @ 24V:
- 3000A peak current;
- 1000A starter current.
Output current @ 12V:
- 6000A peak current;
- 2000A starter current.
Copper cables:
- PVC insulated 25mm
Cable length:
- 220cm.
Output socket:
- 12V DC / max. current 10A.
General features:
- re-settable safety switch for output overload;
- automatic charging level reset switch;
- "cigar-lighter" type socket, 12V DC.
Weight:
- 39kg.
Standard accessories:
- T-CHARGE 12 Power supply / Battery charger (Fig. B).
4
2.
2.