Publicidad
Idiomas disponibles
Idiomas disponibles
Alarm mute for the PROGRAMME
END
The alarm for the programme end may be
muted as follows:
IMPORTANT
The dishwasher must be ALWAYS off
before start this procedure.
1. Hold down the FIRST "PROGRAMME"
button (from the right) and at the same
time switch on the dishwasher by
pressing the "ON/OFF" button (a brief
audible signal will sound).
2.
Keep the "PROGRAMME" button pressed
for at least 15 seconds (during this time,
2 audible signals will sound).
3.
Release the button when the second
audible signal sounds (3 "PROGRAMME
SELECTION" indicator lights will come
on).
4.
Press the same button again: the 3
indicator lights (which indicate that the
alarm is activated) will start flashing (to
indicate that the alarm is off).
5.
Turn off the dishwasher by pressing the
"ON/OFF" button to confirm the new
setting.
To turn the alarm on again, follow the same
procedure.
Fault signals
If malfunctions or faults occur when a
programme is running the indicator light
that corresponds to the selected cycle
(2 indicator lights for the "COLD RINSE"
programme) will flash rapidly and the alarm
sounds.
In this event, turn the dishwasher off by
pressing the "ON/OFF" button.
After checking to make sure the water
inlet hose tap is open, that the drain
hose is not bent and that the siphon or
filters are not clogged, set the selected
programme again.
If the anomaly persists, contact Customer
Service Department.
IMPORTANT
This dishwasher is equipped with an
anti-overflow safety device which will
automatically discharge any excess
water should a problem occur.
WARNING!
To ensure the correct operation of
the anti-overflow safety device, we
recommend that the dishwasher is
not moved or tilted during operation.
If however it is necessary to tilt or
move the dishwasher, please ensure
that the washing cycle is complete
and that there is no remaining water
inside the dishwasher.
6
WATER SOFTENER UNIT
Depending on the source of the supply,
water contains varying amounts of limestone
and minerals which are deposited on the
dishes leaving whitish stains and marks.
The higher the level of these minerals
present in the water, the harder the water is.
The dishwasher is fitted with a water
softener unit which, through the use of
special
regenerating
salt,
supplies
softened water for washing the dishes.
The degree of hardness of your water can
be obtained from your water supply
company.
Regulating the water softener
The softener unit can treat water with a
hardness of up to 90°fH (French grading)
or 50°dH (German grading) through 6
different settings.
The table below lists different degrees of
water hardness with the corresponding
setting for the softener unit.
Water
hardness
No indicator
0
0-5
0-3
NO
lights
Indicator light
6-15
4-9
YES
1
1
Indicator lights
16-30
10-16
2
YES
1,2
Indicator lights
17-25
*3
31-45
YES
1,2,3
Indicator lights
46-60
26-33
4
YES
1,2,3,4
Indicator lights
5
61-90
34-50
YES
1,2,3,4
flashing
"PROGRAMME SELECTION" indicator lights
"PROGRAMME" buttons
* The water softener unit is set in the
factory at level 3, as this is suitable for
the majority of users.
According to the degree of hardness of
your water, regulate the softener unit in the
following way:
IMPORTANT
The dishwasher must be ALWAYS
off before start this procedure.
1. Hold down the FIRST "PROGRAMME"
button (from the right) and at the same
time switch on the dishwasher by
pressing the "ON/OFF" button (a brief
audible signal will sound).
2. Keep
the
"PROGRAMME"
pressed for at least 5 seconds, UNTIL
an audible signal sounds. Some
"PROGRAMME SELECTION" indicator
lights will come on to indicate the
current water softener setting level.
3. Press the same button again to select
the required water softener level: each
time the button is pressed, one indicator
light will come on (the water softener
level is indicated by the number of lights
on). For level 5, 4 lights will flash, for
level 0 all lights will be off.
4. Turn off the dishwasher by pressing the
"ON/OFF" button to confirm the new
setting.
WARNING!
If any problem occurs, turn the
dishwasher off by pressing the
"ON/OFF" button and start the
procedure again from the beginning
(STEP 1).
"ON/OFF" button
7
button
Publicidad
