Publicidad
Idiomas disponibles
Idiomas disponibles
E N G L I S H
• Take the time to thoroughly read and understand this manual prior to
operation.
• Remove the saw from the packaging material carefully.
• Remove the 4 hex. headed screws securing the machine to the
wooden packaging.
• Release the head lock down knob (14) to raise the head of the
machine.
Description (fig. A1 - A4)
A1
1 Bevel locking handle
2 Rotating table locking knobs
3 Mitre fence
4 Plastic feet
5 Plastic handles/work supports
6 Head lock up release lever
7 Switch
8 Additional saw bench table locking knob
9 Moveable lower blade guard
10 Adjustable cut - to length gauge/material support (optional accessory)
11 Rotating work table
12 Steel base
13 Mitre latch lever
14 Head lock down knob
A2
15 Saw bench table
16 Riving knife
17 Upper saw blade guard
18 Rip fence
19 Fixed lower guard (for use in bench saw position)
Optional accessories
A3
20 Material clamp*
A4
9 Adjustable cut - to length gauge/material support*
* refer to sales literature
Electrical safety
The electric motor has been designed for one voltage only. Always check
that the power supply corresponds to the voltage on the rating plate.
Mains plug replacement (U.K. & Ireland only)
• Should your mains plug need replacing and you are competent to do
this, proceed as instructed below. If you are in doubt, contact an
authorized D
WALT repair agent or a qualified electrician.
E
• Disconnect the plug from the supply.
• Cut off the plug and dispose of it safely; a plug with bared copper
conductors is dangerous if engaged in a live socket outlet.
• Only fit 13 Amperes BS1363A approved plugs fitted with the correctly
rated fuse (1).
• The cable wire colours, or a letter, will be marked at the connection
points of most good quality plugs. Attach the wires to their respective
points in the plug (see below). Brown is for Live (L) (2) and Blue is for
Neutral (N) (4).
• Before replacing the top cover of the mains plug ensure that the cable
restraint (3) is holding the outer sheath of the cable firmly and that the
two leads are correctly fixed at the terminal screws.
en - 3
Never use a light socket.
Never connect the live (L) or neutral (N) wires to the earth pin
marked E or
.
Using an extension cable
If an extension cable is required, use an approved triple-core extension
cable suitable for the power input of this tool (see technical data).
The minimum conductor size is 1.5 mm
unwind the cable completely. Also refer to the table below.
2
Conductor size (mm
)
0.75
1.00
1.50
2.50
4.00
Voltage
Amperes
115
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
230
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
Assembly and adjustment
Prior to assembly and adjustment always unplug the tool.
Fitting and adjusting the side handles (fig. B1 - B3)
The machine is supplied with two plastic side handles (5) for easy holding
of the base when carrying.
These handles are constructed in two parts in order to be adjustable.
They also act as material supports on each side of the base.
• To mount, take one flat part (22) and one part with a curved edge (21)
and place the serrated surfaces together. The serrations allow
adjustment, whilst firmly locking them together (fig. B1).
• Place the handles against the side of the base (12), lining up the holes
in the handles with the set of holes nearest to the front provided in the
base. Ensure the curved edge is to the top and pointing to the centre
of the table (fig. B2).
• Using the flat HD screws M6 x 16, four washers D6 and four Hex nuts
M6, screw the handles on loosely. Check that the flange on the bottom
of the flat section is under the edge of the base.
• Having mounted both handles, take a piece of flat wood and lay it up
against the mitre fence (3) and across the table. Ensure that the tops of
the handles are touching the wood (fig. B3).
• Now firmly tighten all bolts.
2
. When using a cable reel, always
Cable rating (Amperes)
6
10
15
20
25
Cable length (m)
7.5
15
25
30
45
Cable rating (Amperes)
6
6
6
6
6
6
6
6
6
15
6
6
10
15
20
10
10
15
20
20
15
15
20
25
25
20
20
25
-
-
6
6
6
6
6
6
6
6
6
6
6
6
6
6
10
10
10
10
10
15
15
15
15
15
20
20
20
20
20
25
60
10
15
20
25
-
-
6
6
15
15
20
-
14
Publicidad
