Clock Button; Light Button - MESTIC RTA-2500 Manual

5 FAN button
Press this button, Auto, Low, Middle, High speed can be circularly selected. After powered on, Auto fan is not available
for this mode. When pressing AUTO button, the fan speed
will not change.
Note: Under the Dry mode, the fan speed isn't adjustable, low fan speed is imperative, but when operating this
button, the wireless adjustable, low fan speed is imperative.
6 button
Press this button turn on swing function; 4s later, press this button to turn off the swing and it will operate like that
circularly. Other air conditioners, press this button, to set up swing angle, which circularly changes as below:
This is an universal use remote controller. If remote controller sends the following three kinds of status that the swing
status of main unit will be:
When the guide louver start to swing up and down, if turn off the Swing, the air guide louver will stop at current
position. which indicates the guide louver swings up and down between that all five positions.

7 CLOCK button

Press this button, the clock can be set up, signal
pressing + or - button, if continuously press this button for 2 seconds above, in every 0.5 seconds, the value on ten
place of Minute will be increased 1. During blinking, repress the Clock button, signal
and denotes the setting succeeded. After powered on,12:00 is defaulted to display and signal
there is signal be displayed that denotes the current time value is Clock value, otherwise is Timer value.
8 LED button
Press this button can turn on or turn off the LED light on the panel.
9 TIMER ON button
Timer On setting: Signal "ON" will blink and display, signal
timer on setting status. During 5 seconds blink, by pressing + or - button to adjust the time value of numerical section,
every press of that button, the value will be increased or decreased 1 minute. Hold pressing + or - button, 2 seconds
later, it quickly change, the way of change is: During the initial 2.5 seconds, ten numbers change in the one place of
minute, then the one place is constant, ten numbers change in the tens place of minute at 2.5 seconds speed and carry.
During 5s blink, press the Timer button, the timer setting succeeds. The Timer On has been set up, repress the timer
On button, the Timer On will be canceled. Before setting the Timer, please adjust the Clock to the current actual time.
14
blink and display. Within 5 seconds, the value can be adjusted by
will be constantly displayed
will be displayed. If
will conceal, the numerical section will become the
10 TEMP-knop
Press this button, could select displaying the indoor setting temperature or indoor ambient temperature. When the
indoor unit firstly power on it will display the setting temperature, if the temperature's displaying status is changed
from other status to " ", displays the ambient temperature, 5s later or within 5s, it receives other remote control
signal that will return to display the setting temperature. if the users haven't set up the temperature displaying status,
that will display the setting temperature. (This function is applicable to partial of models)
After powered on, the setting temperature displaying is defaulted, (according to cust- omers requirements to display,
if there is no requirement that will default to display the presetting temperature and there is no icon displayed on
wireless remote control). Press this button, (When displaying
displaying ) will display indoor ambient temperature,
displays indoor ambient temperature, if received the other remote control signal, it will display presetting temperatu-
re, 5s later, will back to display the ambient temperature.
(This function is applicable to partial of models)
11 TIMER OFF button
Once press this key to enter into TIMER OFF setup, in which case the TIMER OFF icon will blink.
The method of setting is the same as for TIMER ON.
12 TURBO button
In Cool or Heat mode, press this button can turn on or turn off the Turbo function. After turned on the Turbo function,
its signal will be displayed. When switching the mode or changing fan speed, this function will be canceled automa-
tically.
13 SLEEP button
Press this button, Sleep On and Sleep Off can be selected. After powered on, Sleep Off is defaulted. After the unit is
turned off, the Sleep function is canceled. After Sleep function set up, the signal of Sleep will display.In this mode, the
time of timer can be adjusted. Under Fan and Auto modes, this function is not available.

14 LIGHT button

Press this button to select LIGHT on or off in the displayer. When the LIGHT on is set, the icon
and the indicator light in the displayer will be on. When the LIGHT off is set, the icon
indicator light in the displayer will be off.
), will display presetting temperature; (when
current displaying status will not be changed. If current
will be displayed
will be displayed and the
15