THOMSON ROC4206 Manual De Instrucciones página 6

Method B – 4-digit codes Programming
Before you start programming, you must find the code of
the set to be controlled.
Refer to the list provided with these instructions, page
II of the codes.
1. Switch on the set you want to control.
2. Hold down the SETUP until the red indicator
lamp remains lit (the indicator light remains on for
a few seconds to give you the time to proceed with
the following steps.The indicator lamp flashes when
this time is almost up, and then goes off).
3. Press the key that corresponds to the type of
equipment you want to control: TV, DVD/VCR...
4. While the indicator is lit, enter the first digit of the
4-digit code proposed for the set to be controlled
(example: 0036 for Thomson). The red indicator
then goes off if the code is correct or flashes, if the
code is not on the list.
5. Direct the remote control towards the set and try
to switch it off by pressing the B key.
6. Should the set not switch off, repeat step 2. Then
type in the next 4-digit code. Try to switch off the
set by pressing B key once. Repeat this procedure
by trying out each of the 4-digit codes.
Check of the programming:
In principle, your set is ready for receiving the remote control
commands.Check your remote control for proper functioning
by performing the test described on page 3.
Method C – Programming by means of
Should none of the codes work, you still have the possibility
of retrieving the appropriate code without having to perform
any input.
1. Switch on the set you want to control.
2. Hold down the SETUP until the red indicator
lamp remains lit (the indicator light remains on for
a few seconds to give you the time to proceed with
the following steps.The indicator lamp flashes when
this time is almost up, and then goes off).
3. Press the key that corresponds to the type of
equipment you want to control: TV, DVD/VCR...
4. Direct the remote control towards the set and try
to switch it off by pressing the B key.
5. If the set you want to control switches off, press c
to memorise the subcode.
6. Should the set not switch off, press B key, as
many times as required (up to 200 times), until the
set switches off. Wait approximately one second
between key presses to give the red indicator lamp
enough time to go off and light up again. Proceeding
this way will enable you to see whether the set
responds or not.
7. Immediately upon the switching-off of the set to be
controlled, press c to store the subcode.
06_GB.indd 2
code retriever
Note:
If you want to assign another type of product than those
mentioned on the remote control, begin by entering a code
that corresponds to the product you want to programme
(a 4-digit code that you will find in the code booklet – see
method B).
Example: if you want to control a satellite receiver with the
DVD/VCR key, begin by entering a satellite code (any
satellite, for example: 0603 for a Thomson satellite receiver)
then begin the procedure.
Check of the programming:
In principle, your set is ready for receiving the remote control
commands.Check your remote control for proper functioning
by performing the test described on page 3.
Method D - Automatic code search
With this method, the remote control scrolls through the full
code list by sending an IR signal to the set to be controlled
remotely. Proceed as follows:
1. Check that your equipment is on. If not, switch it on
manually.
2. Hold down the SETUP until the red indicator
lamp remains lit (the indicator light remains on for
a few seconds to give you the time to proceed with
the following steps.The indicator lamp flashes when
this time is almost up, and then goes off).
3. Release the SETUP key.
4. Press the key corresponding to the type of
equipment (for example TV).
5. Press the PROG+ key once. After a few seconds
the remote control begins to list all the codes
included in the library (around 1 code per second).
Press PROG+ a second time to reduce the speed
of the test (1 code every 3 seconds).As soon as the
device changes channel you must immediately press
c to record the code and stop the listing. If you
have gone past the code, you can go back to the
previous code by pressing PROG- as many times
as necessary (you can go forward by pressing B or
PROG+. As soon as the device reacts again, press
c to record the code.
Note:
If you want to assign another type of product than those
mentioned on the remote control, begin by entering a code
that corresponds to the product you want to programme
(a 4-digit code that you will find in the code booklet – see
method B).
Example: if you want to control a satellite receiver with the
DVD/VCR key, begin by entering a satellite code (any
satellite, for example: 0603 for a Thomson satellite receiver)
then begin the procedure.
Method E – Programming for control of a COMBO
(combined TV-VCR,TV/DVD, DVD/VCR, ... set)
Depending on the COMBO group (TV/VCR, DVD/VCR, etc.)
and the make, you will be required to enter a single code for
both devices in the COMBO, or to enter two codes, one code
per device. Consult the separate list to discover this. Before
you start programming, you must find the subcode or code
of the subset to be controlled (television or video recorder).
2
27/10/06