Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
3.8. Adjusting the harness and headrest height in an installation with a
5-point harness. Groups 0+/1.
Proper adjustment of the height of the harness ensures the child will be
seated correctly. The harness should be adjusted to the height of the child's
shoulder or slightly above; never behind the child's back or level with the ears
(fig. 3.15).
IMPORTANT! The shoulder straps should not be passed behind the child's
back at or above ear level.
1. Loosen the harness straps by pulling them gently while pressing the harness
adjustment button (G). (fig. 3.8).
2. Pull the headrest height adjuster
time. Select the correct height for the shoulder straps
the correct position for the child by releasing the adjuster (fig. 3.8).
3.9. Adjusting the headrest. Groups 2/3.
A correctly adjusted headrest ensures that the diagonal part of the safety
belt is ideally positioned, offering the child the best possible protection.
The headrest should be adjusted so that a space equivalent to two fingers
remains between the headrest and the child's shoulders.
To adjust the height of the headrest:
1. Pull the headrest height adjuster
This will unlock the headrest (fig. 3.8).
2. Now you will be able to move the headrest to the desired height. When the
adjuster is released the headrest will remain locked in the chosen position.
3. Place the safety seat on the car seat.
4. Sit the child in the seat and check the height. Repeat the process until the
correct height is achieved.
4. CAR SEAT REARWARD-FACING INSTALLATION.
GROUP 0+/1
GROUP 0+/1 only. From
NOTICE
birth to 4 years aprox. (0-18 Kg)
IMPORTANT: It is advisable to use the seat backward-facing as long as possible.
If the height of the child or the size of the vehicle prevents the child to travel
rearward-facing until 18kg, we advise to maintain rearward-facing travel
position up to 13 kg. If necessary, the seat can be installed forward-facing when
the child reaches 9kg of weight.
32
(K)
and the headrest
(A)
at the same
(E)
and fix them in
(K)
and the headrest at the same time.
NOTICE: This car seat offers different installation options (installation table,
chapter 2) WITH or WITHOUT Isoclick Fix
• For a car seat installation using Isoclick Fix
please start from section 4.1.
• For a car seat installation using only the vehicle´s belt, please start from
section 4.2
4.1 Connecting the Isoclick Fix
arms in a rearward-facing installation.
®
Group 0+/1. (optional)
• Preparing the Isoclick Fix
system
®
1.
If your vehicle has not been fitted with the ISOFIX latch guides as
standard, fit the two latch guides
(fig. 4.1)
2. By turning, extract both Isoclick Fix arms. Move the arms from side to side
until you hear the click indicating that they are fully locked.
3. Make sure that the displayed arms corresponds to the selected installation,
group 0 (rearward facing)
(Q)
or group 1/2/3 (forward facing)
The insertion guides facilitate the installation of the safety seat with the aid
of the ISOFIX securing points and prevents damage to the upholstery. When
not in use they should be removed and stored in a safe place. In vehicles with
a reclining back the insertion guides should be removed before the seat is
reclined. Problems that may arise are generally the result of accumulation of
dirt or foreign bodies in the insertion guides and the clasps. To solve this type
of problem simply clean the part in question.
4. Make sure the 5-point harness of the safety seat has been correctly
installed (see section 3).
5. Follow the steps described in section 3.8.
6. Recline the seat fully. Pull the lever
recline to position 4 without releasing the lever. Release the lever when
the seat is in the desired position (fig. 4.3).
7. Make sure the Isoclick Fix
arms
®
backward facing (group 0+/1).
8. Place the seat in the back seat of the vehicle in opposite direction of
travel.
9. Hold the safety seat with both hands and insert the two Isoclick Fix
(Q)
firmly into the insertion guides
both sides. The red button will partially change to green on both sides
(fig. 4.4).
10. Shake the seat to check that it is correctly anchored to the vehicle's
ISOFIX points.
connectors.
®
connectors and vehicle's belt,
®
(T)
that came with the safety seat.
(O)
(fig. 4.2).
(I)
forward and adjust the angle of
(Q)
are displayed to install the car seat
arms
®
(T)
until they fasten with a click on
33
Publicidad
Tabla de contenido
