Baby auto DUPLA Duofix DS20 Manual De Uso página 19

4. Hold the safety seat with both hands and insert the two Isoclick Fix
(O) firmly into the insertion guides
sides. The red button will partially change to green on both sides (fig. 5.4).
5. Shake the seat to check that it is correctly anchored to the vehicle's
ISOFIX points.
6. Push the safety seat towards the back using a firm, constant pressure on
both sides until it rests firmly against the vehicle seat. If necessary, adjust
the reclining of the vehicle´s seat backrest to ensure that the child seat
rests correctly. (fig. 5.5).
• Uninstalling Isoclick Fix system
®
1. To free the Isoclick Fix anchoring, press the Isoclick Fix system unlock
®
buttons (P), in order to free the seat from the vehicle ISOFIX anchoring
system (fig. 5.6).
5.2 Fastening the seat with the vehicle's belt in a forward-facing
installation. Group 1
1. Pull the lever (I) forward and adjust the angle of recline to position 1, 2,
or 3 without releasing the lever. Release the lever when the seat is in the
desired position (fig. 5.7).
2. Place the seat in the back seat of the vehicle in the direction of travel
3. Pass the vehicle seat belt through the slot on the back of the safety seat
(U) (fig. 5.9) until it appears at the exit.
4. Buckle the vehicle seat belt until you hear a click (fig. 5.10).
5. To ensure the belt holds tighten the seat (fig. 5.11), you can press with the
knee on the seat at the same time you are fitting the belt to the seat.
6. Ensure the straps are not twisted or knotted at any point.
For the safety of the child the following checks should be made before every
trip:
• The safety seat is firmly installed in the vehicle.
• The straps are not twisted.
• The safety seat straps are firmly fastened around the child's body, without
squashing it.
36
arms
®
(T) until they fasten with a click on both
(E)
• The shoulder straps are correctly adjusted and not twisted.
• The clasps are correctly inserted into the belt buckle (F).
5.3 Fastening the child in the seat. Group 1
To install the child correctly follow the steps described in section 4.3.
6. CAR SEAT FORWARD-FACING INSTALLATION.
GROUP 2.
(Fastening the child using 5 point harness / Optional)
GROUP 2 only. From
NOTICE
4 years to 6 years (15-25 Kg)
This seat allows, optionally, the child installation with harness in Group 2. As
long as the vehicle has ISOFIX anchorages and Top Tether anchorage.
For the Isoclick Fix system and vehicle belt seat installation, follow the steps
®
described in sections 5.1 and 5.2. For the Top Tether system Installation, see
the following steps
1. Take the Top Tether and press the Top Tether regulator
strap (fig. 6.1).
2. Hook the safety clasp (S) to the Top Tether anchor point recommended in
your vehicle instruction (fig. 6.2).
IMPORTANT! Make sure not to use the luggage clip instead of
the Top Tether anchor clip. Look for this symbol in your vehicle:
3. To tighten the Top Tether, take up any slack by pulling the free end of the
belt through the Top Tether adjuster
correctly tightened when the green tension indicator extends 1 mm (fig.
6.4).
4. Follow the 1, 2 and 3 steps from the section 3.3 of manual to take out the
buckle, insert it again changing the position 1 to 2 (fig. 6.5).
6.1 Fastening the child in the seat. Group 2
To fastening the child, follow the steps described in section 4.3
(R) to stretch the
(R) (fig. 6.3). The Top Tether will be
37