Suntec Wellness BBQ-9462 Manual De Instrucciones página 18

lower elbow pipe (9). Hold the handle from the substructure and remove it (see figure 6).
7. Place the grease collecting bowl (b) in the supplied mounting bracket located in the rear part of the
machine base. Position the opening on the grease collecting bowl so that it is located in the middle of
the shell-shaped base (tip: fill a little water into the bowl for easier cleaning). Mount the butterfly screw
(N3) to secure the grill to the substructure of the unit (see figure 7).
8. To mount the grill plate (3) on the base of the appliance (5), hold the right side of the grill plate (3) high
and insert the connecting socket (15) into the opening on the appliance base (12) provided for this
purpose. Lower the right side of the grill plate (13) until it is horizontal and firmly fixed on the appliance's
base (5). To remove the grill plate (3), lift it up on the right-hand side and pull the connection socket (15)
out of the opening on the base (12). Before removing the grill plate, please make sure that it has cooled
down and is no longer in use (see figure 8).
Attention: The grill plate must be used together with the bowl-shaped base.
9. Insert the screw (N4) with a silicone washer and the lid hook through the inner side of the grill hood.
Attach the handle to the outside of the hood. Turn it clockwise to attach the grill hood. During installation,
please adjust the angle and direction between the lid hook (G2) and the handle (2) to determine the
alignment (see figure 9).
10. Insert the removable thermostat (13) into the connecting socket (15). If you wish to remove the
thermostat (13), hold the handle on the base of the unit to prevent scratches to the unit or substrate (see
figure 10).
11. The grill hood can be used as a wind shield when you are outside grilling. To do this, hook the lid hook
located on the inside of the lid into the notch at the rear edge of the grill plate (see figure 11).
Components of BBQ-9462
1. Grill hood
2. Hood handle
3. Grill plate
4. Grease collecting bowl
5. Base of appliance
6. Upper stand tube
7. Decoration ring
8. Lower stand tube
9 A. Stand foot
(The corresponding pictures can be found in the front of this manual.)
Installation of BBQ-9462
1. Place the stand base upside down on a smooth, firm surface and insert the feet into the guide slots as
shown in figure 1 until you hear a click.
2. To fix the stand, place the washer (15) on the stand and tighten it with the screws (16) provided (see
figure 2).
3. Screw half of the threaded rod (a) into the lower stand tube (8). Then place the decoration ring (7) on
the threaded rod (a) and screw the upper stand tube (6) to the threaded rod (a) (see figure 3).
4. Connect the grill stand base (9) to the lower stand tube (8) to complete the grill stand. (the grill can be
used with or without stand) (see figure 3).
5. Place the base of the appliance (5) on the grill (make sure that the grill is placed on a dry, flat and stable
surface) (see figure 4).
6. Place the grease collecting bowl (4) into the provided holder of the base (5). Fasten the opening of the
grease collecting bowl with a screw (fill the bowl with a little water, which makes it easier to clean) (see
figure 5).
7. Place the grill plate (3) on the base (5). First, insert the connecting socket (14) into the opening (11)
provided for this purpose. Then place the grill plate horizontally on the base (see figure 6).
8. Install the hood handle (2) with the screw (d) and the hook on the metal hood (C) as shown in figure 7.
Then place the grill hood on the grill surface (see figure 8).
9. Push the removable thermostat (12) as far as possible into the grill's socket (see figure 8).
10. The grill hood can be used as a wind shield when you are grilling outside. To do this, hook the lid hook
located on the inside of the lid into the notch at the rear edge of the grill plate (see figure 9).
Prior to first use
•
Please remove all packaging material and clean the grill plate (3), the grease collecting bowl (4) and
grill hood (1) thoroughly.
Important: Please allow all parts to dry thoroughly, especially the connecting socket. Never immerse
the thermostat or cord in water or any other liquid.
•
Please heat the grill with the lid closed for about 10 minutes at maximum setting, without any food.
Residues from the manufacturing process could cause odour and smoke when the device is used for
the first time. This is normal and will disappear after a short time.
9 B. Stand base
10. Handle of base
11. Opening for appliance's socket
12. Detachable thermostat with cord
13. Temperature indicating lamp
14. Appliance's socket
15. Washer
16. Screws