DeWalt DWE4557 Traducido De Las Instrucciones Originales página 37

Ocultar thumbs Ver también para DWE4557:
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 43
Soft Start Feature
DWE4579, DWE4579R, DWE4597,
DWE4599
The soft start feature allows a slow speed build-up to avoid an
initial jerk when starting. This feature is particularly useful when
working in confined spaces.
Auto-balance Feature
DWE4599 only
The auto-balance feature continuously adjusts balance to
reduce the vibration of the tool when it is running. This
improves user comfort during the operation and is particularly
useful when using the tool for long periods of time.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Before
reconnecting the tool, depress and release the trigger
switch to ensure that the tool is off.
Attaching Side Handle (Fig. F)

WARNING: Before using the tool, check that the handle is
tightened securely.
For grinding, screw the side handle
holes
 17 
on either side of the gear case (Fig. F).
For cutting, screw the side handle
or into one of the holes
 18 
 17 
Fitting and Removing a
Backing Pad/Sanding Sheet (Fig. A, D)
1. Place the tool on a table or flat surface, with the guard
facing up.
2. Remove the backing flange
3. Place the rubber backing pad correctly onto the spindle
4. Place the sanding sheet on the rubber backing pad.
5. Screw the threaded clamp nut
ring on the threaded clamp nut must face towards the
rubber backing pad.
6. Press the spindle lock button
until it locks in position.
7. Tighten the threaded clamp nut
pin spanner.
8. Release the spindle lock.
9. To remove the rubber backing pad, loosen the threaded
clamp nut
 14 
with the two-pin spanner.
Fitting a Wire Cup Brush
Screw the wire cup brush directly onto the spindle without the
use of the spacer and threaded flange.
 5 
tightly into one of the
 5 
tightly into the top hole
on either side of the gear case.
 12 
.
 13 
 14 
onto the spindle. The
 3 
and rotate the spindle
 13 
 14 
with the two-
Mounting and Removing the Guard
(Fig. B)

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Before
reconnecting the tool, depress and release the trigger
switch to ensure that the tool is off.

CAUTION: Guards must be used with this grinder.
When using the DWE4557, DWE4559, DWE4579, DWE4579R,
DWE4597 or the DWE4599 grinder for cutting metal or masonry
a Type 1 guard MUST be used. Type 1 guards are available at
extra cost from D
WALT distributors.
e
nOTE: Please refer to the Grinding and Cutting Accessory
Chart at the end of this section to show other accessories that
can be used with these grinders.
1. Place the angle grinder on a table, spindle up.
2. Release the clamping lock
tool as shown.
3. Align the lugs
 9 
with the notches
4. Press the guard down and rotate it to the required posiiton.
5. If required, increase the clamping force by tightening the
screw
 11 
.
6. Tighten the clamping lock.
To remove the guard, release the clamping lock.

CAUTION: If the guard cannot be tightened by the
adjusting screw, do not use the tool. To reduce the risk of
personal injury, take the tool and guard to a service centre
to repair or replace the guard.
Fitting and Removing a Grinding or Cutting
Disc (Fig. A, C–E)

WARNING: Do not use a damaged disc.
.
1. Place the tool on a table, guard up.
2. Fit the backing flange
(Fig. C).
3. Place the disc
on the backing flange
 15 
fitting a disc with a raised centre, make sure that the raised
centre
 16 
is facing the backing flange
4. Screw the threaded clamp nut
(Fig. E):
a. The ring on the threaded clamp nut
towards the disc when fitting a grinding disc (Fig. E1);
b. The ring on the threaded clamp nut
from the disc when fitting a cutting disc (Fig. E2).
5. Press the spindle lock button
until it locks in position (Fig. D).
6. Tighten the threaded clamp nut
spanner supplied. nOTE: Refer to Fitting and Removing
a Grinding or Cutting Disc with a Keyless Flange when
using the DWE4579R.
7. Release the spindle lock.
EnGLIsh
and hold the guard
over the
 8 
 4 
 10 
.
 12 
correctly onto the spindle
(Fig. D). When
 12 
 12 
.
 14 
onto the spindle
 13 
 14 
must face
 14 
must face away
 3 
and rotate the spindle
with the two-pin
 14 
 13 
 13 
35

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Dwe4559Dwe4579Dwe4579rDwe4597Dwe4599

Tabla de contenido