Publicidad
Idiomas disponibles
Idiomas disponibles
Attaching the Camera Wand
1. Gently push the camera wand connector (Figure
onto the wand connector
2. Turn the knurled nut
30
NOT over-tighten the camera wand.
3. Turn the Power/LED Brightness Wheel
the brightness of the 4 LEDs at the end of the wand
To remove the wand, turn the knurled nut
as shown on the knurled nut.
Attaching Accessories
All accessories (Figure
) attach to the camera end of the
D
wand in the same manner (Figure
hard to reach places and recovery of small objects.
1. Slide the retainer sleeve
wand (if not assembled).
2. Insert the small hook on the end of the attachment into the
hole
on the wand
41
7
3. Turn the retainer sleeve so the thin, raised channel
lined up with the attachment.
4. Slide the retainer sleeve over the attachment to hold it in
place.
Connecting a Video Output Device
You can output the images you capture using the inspection
camera to an RCA style video input device, a micro SD card, or
a personal computer that has a USB port.
To an RCA Video Input Device
1. Insert the 3 mm jack on the video adapter cable
(Figure
) into the video output port
17
A
the LCD Monitor.
2. Connect the other end of the cable into any compatible RCA
style video input device.
To a Micro SD Card
• Insert the micro SD card (Figure
SD card slot
and gently press the card until it clicks into
10
place. When the micro SD card is inserted successfully
a "micro SD card icon"
33
otherwise, the "no SD card icon"
• When the micro SD card is full, the MEMORY FULL message
will appear on the screen. You can delete photos and videos
you no longer need, output files to a PC before deleting them
from the card, or use another micro SD card.
• To remove the micro SD card, gently press the card inward to
release the card and then carefully pull the card from the slot.
A
.
1
clockwise until firmly seated. DO
to the left to set
5
counter-clockwise,
30
) to aid in the inspection of
E
onto the camera end of the
16
.
40
on the side of
12
)into the micro
19
A
will appear on the LCD Monitor;
will appear.
34
To a Personal Computer
1. Press
for 3 seconds to turn off the LCD monitor.
)
31
2. Insert the USB Cable (Figure
on the LCD Monitor.
3. Connect the other end of the USB cable into a USB port on
the PC.
.
4. Press
for 3 seconds to turn on the LCD monitor. On
7
the LCD Monitor, view USB.
The computer will recognize the new hardware, which you may
browse by double-clicking on the My Computer icon on your
desktop, and then navigate into the Mobile Disk Directory.
Operation
The LCD Monitor has a wireless connection to the camera base,
so you can slide it off the base and handle it separately when
you are taking a photo or recording a video.
Taking a Photo
1. Make sure the camera is in real-time monitoring mode
is
(Figure
).
F
2. Easily guide the camera wand into position to take the
photo. Do not apply excessive force.
3. When you are ready to take the photo, press
Recording a Video
1. Make sure the camera is in real-time monitoring mode
(Figure
).
F
2. Easily guide the camera wand into position to take the
video. Do not apply excessive force.
3. When you are ready to start recording, press
Recording Active icon
will be displayed on the screen.
32
4. To stop recording, press
icon will no longer appear on the screen.
NOTE: The video will automatically be saved as an individual
file every 10 minutes.
Viewing a Recorded Video or Photo
to display the System Settings (Figure
1. Press
2. Display a list of the saved photos and videos (Figure
• Highlight
• Press
.
3. Highlight the desired photo or video.
4. Press
to play the video or show the photo.
) into the USB port
18
A
and the length of the recording
36
again. The Recording Active
and press
, or
GB
11
.
. The
).
P
).
Q
11
Publicidad
