Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
In spite of the application of the relevant safety regulations and the
implementation of safety devices, certain residual risks cannot be avoided.
These are:
- Impairment of hearing.
- Risk of accidents caused by the uncovered parts of the rotating saw
blade.
- Risk of injury when changing the blade.
- Risk of squeezing fingers when opening the guards.
- Health hazards caused by breathing dust developed when sawing
wood, especially oak, beech and MDF.
Electrical safety
The electric motor has been designed for one voltage only. Always check
that the power supply corresponds to the voltage on the rating plate.
Your Elu tool is double insulated in accordance with
EN 50144; therefore no earth wire is required.
Mains plug replacement (U.K. & Ireland only)
• Should your mains plug need replacing and you are competent to do
this, proceed as instructed below. If you are in doubt, contact an
authorized Elu repair agent or a qualified electrician.
• Disconnect the plug from the supply.
• Cut off the plug and dispose of it safely; a plug with bared copper
conductors is dangerous if engaged in a live socket outlet.
• Only fit 13 Amperes BS1363A approved plugs fitted with the correctly
rated fuse (1).
• The cable wire colours, or a letter, will be marked at the connection
points of most good quality plugs. Attach the wires to their respective
points in the plug (see below). Brown is for Live (L) (2) and Blue is for
Neutral (N) (4).
• Before replacing the top cover of the mains plug ensure that the cable
restraint (3) is holding the outer sheath of the cable firmly and that the
two leads are correctly fixed at the terminal screws.
Never use a light socket. Never connect the live (L) or neutral
(N) wires to the earth pin marked E or
For 115 V units with a power rating exceeding 1500 W, we recommend to
fit a plug to BS4343 standard.
Using an extension cable
If an extension cable is required, use an approved extension cable suitable
for the power input of this tool (see technical data). The minimum
conductor size is 1.5 mm
2
.
When using a cable reel, always unwind the cable completely.
Also refer to the table below.
18
Conductor size (mm
0.75
1.00
1.50
2.50
4.00
Voltage
115
230
Unpacking (fig. A1, A2 & B)
Remove the saw from the packing material carefully using the carrying
handle (9) and the rails (14).
The package contains:
1 Assembled sliding compound mitre saw
1 Saw blade wrench
1 60 teeth 305 mm TCT saw blade
1 Stabilizer
1 Instruction manual
1 Exploded drawing
• Check for damage to the tool, parts or accessories which may have
occurred during transport.
• Take the time to thoroughly read and understand this manual prior to
operation.
• Press down the operating handle (17) and pull out the lock down pin (16),
as shown in fig. B.
• Gently release the downward pressure and allow the arm to rise to its
full height.
Description (fig. A1 & A2)
Your PS374 sliding compound mitre saw has been designed for
professional cutting of wood, wood products, aluminium and plastics.
.
It will perform the sawing operations of cross-cutting, bevelling and mitring
easily, accurately and safely.
A1
1 ON/OFF-switch
2 Lower blade guard
3 Fence, right-hand side
4 Mitre lever
5 Mitre latch
6 Mitre scale
7 Fence, left-hand side
8 Bench mounting holes
9 Base
10 Base stabiliser
11 Bevel lever
11A Bevel stop override button
12 Bevel stop screw
13 Saw blade wrench
14 Rails
2
)
Cable rating (Amperes)
6
10
15
20
25
Cable length (m)
7.5
15
Amperes
Cable rating (Amperes)
0 - 2.0
6
6
2.1 - 3.4
6
6
3.5 - 5.0
6
6
5.1 - 7.0
10
10
7.1 - 12.0
15
15
12.1 - 20.0
20
20
0 - 2.0
6
6
2.1 - 3.4
6
6
3.5 - 5.0
6
6
5.1 - 7.0
10
10
7.1 - 12.0
15
15
12.1 - 20.0
20
20
E N G L I S H
25
30
45
60
6
6
6
10
6
6
15
15
10
15
20
20
15
20
20
25
20
25
25
-
25
-
-
-
6
6
6
6
6
6
6
6
6
6
10
15
10
10
15
15
15
15
20
20
20
20
25
-
en - 3
Publicidad
Tabla de contenido
