FIG. 22
SHIPPING/ALIGNMENT
SHIPPING/ALIGNMENT PLUGS
Finish Table Saw Assembly:
Attach rear fence rail to Slide Table support pan (Fig. 23).
You will need: 1 - 10 x 35mm hex head bolt
1 - 10mm flat washer
1 - 10mm lock washer
1 - 10mm nut
Secure bolt with a flat washer, lock washer, and a nut.
Tighten hardware snug.
FIG. 23
STEP 39. Re-check parallel of rails to the saw table top
(Fig. 17). Using your fence face or a straightedge to
extend the table surface over the rear fence rails, make
sure the distance from the saw table top to the rail top
is the same at both the left and right side of the saw
table. If a rail is not aligned correctly, loosen all mount-
ing screws slightly and tap on the rail with a soft ham-
mer or a regular hammer and a block of wood until the
distances are the same.
Tighten the hardware
attached to the saw table securely. Repeat for the
remaining attachment points checking the distance
along the full length of the rail.
STEP 40. See DW746 manual for Table Saw operating
instruction and adjustments.
Miter Guage Assembly
STEP 41. Insert telescoping scale into housing.
Arrange miter gage as shown in Fig. 24. Insert tele-
scoping scale bar into the housing. Align 90˚ mark with
end of outer housing. Tighten clamp.
FIG. 24
PLUGS
Miter Gauge Assembly - Fig. 25:
STEP 42. Attach fence to miter gauge. Loosen wing
nuts (D). Orient fence (A) and slide miter gauge (B)
locking bar to slot (C) in fence. Tighten thumb screws
(D) to lock fence into place, loosen thumb screws to
adjust.
STEP 43. Attach adjustable stop (E) to miter fence.
Slide adjustable stop locking hardware (F) into slot on
top of the fence. Tighten thumb screws to lock fence
into place, loosen thumb screws to adjust.
STEP 44. Attach quick release clamp (G) to miter
gauge. Put locking screw in full-up position. Orient
clamp pointing rearward and drop into top of miter
gauge. Turn clamp 180 degrees to retain.
FIG. 25
A
Miter Gauge Use
Adjust miter gauge angle - Fig. 26
• Align mark on telescoping bar with end of housing (A).
Tighten thumb screw.
Angle Detent System - Fig. 26
• The miter gauge is equipped with a detent system for
easily setting the more frequently used angles. Adjust
miter gauge in the vicinity of the angle desired, press
and hold detent button (B) on bottom of beam and slide
scale in until the detent catches. Tighten thumb screw.
G
E
F
B
C
6
FIG. 26
A
Miter Gauge Calibration - Fig. 27
1. Set the miter gauge to 90˚ using the detent system.
2. Loosen eccentric lock screw (A). Inside housing using
hex key.
3. Turn eccentric (B) to adjust gauge to true 90˚ using cal-
ibration square. Tighten eccentric lock screw.
FIG. 27
Reversing Miter Gauge - Fig. 28
The Miter Gauge can be reversed easily.
1. Loosen fence lock knobs (A), remove fence (B).
2. Remove lock knobs and fence clamp (C) from fence
base (D).
3. Loosen telescoping clamp (E) and pull angle scale out
of housing.
4. Rotate telescoping housing (F) to oposite side.
5. Rotate fence base to other side.
6. Re-enage degree scale into housing.
7. Re-install fence clamp and lock knobs.
D
8. Re-install fence and tighten clamp.
FIG. 28
C
B
D
A
E
F
B
A
B