Stanley FATMAX SFMCL020 Traducido De Las Instrucciones Originales página 7

Hot/Cold Pack Delay:
Green LED Intermittent
Red LED Solid
Note: The compatible charger(s) will not charge a faulty
battery pack. The charger will indicate a faulty battery pack by
refusing to light.
Note: This could also mean a problem with a charger. If the
charger indicates a problem, take the charger and battery
pack to be tested at an authorized service centre.
Leaving the battery in the charger
The charger and battery pack can be left connected with the
LED glowing indefinitely. The charger will keep the battery
pack fresh and fully charged.
Hot/Cold Pack Delay
When the charger detects a battery that is too hot or too
cold, it automatically starts a Hot/Cold Pack Delay, the green
LED (5a) will flash intermittently, while the red LED (5b) will
remain on continuously, suspending charging until the battery
has reached an appropriate temperature. The charger then
automatically switches to the pack charging mode. This
feature ensures maximum battery life.
Battery state of charge indicator (Fig. B)
The battery includes a state of charge indicator to quickly
determine the extent of battery life as shown in figure B. By
pressing the state of charge button (3a) you can easily view
the charge remaining in the battery as illustrated in figure B.
Installing and Removing the Battery Pack from
the tool
To install battery pack (Fig. C)
● Insert battery pack firmly into tool until an audible click is
heard as shown in figure C. Ensure battery pack is fully
seated and fully latched into position.
To remove battery pack (Fig. D)
● Depress the battery release button (4) as shown in
figure D and pull battery pack out of tool.
(Original instructions)
@
Belt hook (Optional extra) (Fig. E, F)
Warning! To reduce the risk of serious personal
injury, ONLY use the tool's belt hook (6) to hang the
tool from a work belt. DO NOT use the belt hook (6)
for tethering or securing the tool to a person or object
during use. DO NOT suspend tool overhead or
@
suspend objects from the belt hook.
Warning! To reduce the risk of serious personal
injury, ensure the screw (7) holding the belt hook
is secure.
Note: When attaching or replacing the belt hook (6), use only
the screw (7) that is provided. Be sure to securely tighten
the screw.
The belt hook (6) can be be attached to either side of the tool
using only the screw (6) provided, to accommodate left- or
right- handed users. If the hook is not desired at all, it can be
removed from the tool.
To move the belt hook, remove the screw (7) that holds the
belt hook (6) in place then reassemble on the opposite side.
Be sure to securely tighten the screw (7).
The belt hook (6) can be be attached by sliding into the
slots (8) on either side of the tool using only the screw (7)
provided, to accommodate left- or right- handed users. If the
hook is not desired at all, it can be removed from the tool.
To move the belt hook, remove the screw (7) that holds the
belt hook (6) in place then reassemble on the opposite side.
Be sure to securely tighten the screw (7).
Note: Various trackwall hooks and storage configurations are
available.
Please visit our website www.stanleytools.eu/3 for
further information.
Switching on and off (Fig. G)
● To switch the torch on press in the switch (1)
● To switch the torch off press in the switch (1)
The pivoting lens (Fig. G)
● For your convienience, the lens (2) can be pivoted into a
range of positions.
Maintenance
Your STANLEY FATMAX tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
@
regular cleaning.
Warning! Before performing any maintenance on
the tool, remove the battery from the tool. Unplug the
charger before cleaning it.
● Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
ENGLISH
7